Author Topic: 850 T lay shaft  (Read 651 times)

Offline timzim

  • New Egg
  • *
  • *
  • Posts: 11
  • Location: wisconsin
850 T lay shaft
« on: April 20, 2021, 03:59:57 PM »
Has anyone else had trouble finding a lay shaft for a 850T? My 5th gear is worn and T3s  eldos ect. shafts are all over. I think the T3 shaft would work if I also replaced the dogs and the sliding sleeve, as those part no. are one off as well.

jwinwi

  • Guest
Re: 850 T lay shaft
« Reply #1 on: April 20, 2021, 05:28:56 PM »
Hey Tim,
Welcome to WG! Somebody with actual knowledge will be along shortly. :boozing:

Offline Antietam Classic Cycle

  • Gaggle Hero
  • *****
  • *
  • Posts: 13539
  • Happily stuck in the past.
    • Antietam Classic Cycle
  • Location: Rohrersville, Maryland
Re: 850 T lay shaft
« Reply #2 on: April 20, 2021, 05:47:28 PM »
Is it #54 in this illustration that you're looking for?



Charlie

Offline timzim

  • New Egg
  • *
  • *
  • Posts: 11
  • Location: wisconsin
Re: 850 T lay shaft
« Reply #3 on: April 21, 2021, 10:15:41 AM »
Yes, That's what I need part no.14213611. The part I was sent was actually a 14213612 I believe.
Thanks Tim

Wildguzzi.com

Re: 850 T lay shaft
« Reply #3 on: April 21, 2021, 10:15:41 AM »

Offline Antietam Classic Cycle

  • Gaggle Hero
  • *****
  • *
  • Posts: 13539
  • Happily stuck in the past.
    • Antietam Classic Cycle
  • Location: Rohrersville, Maryland
Re: 850 T lay shaft
« Reply #4 on: April 21, 2021, 11:15:15 AM »
Any way to tell one from the other at a glance? I have a bin full of 5 spd. munt, may have one.
Charlie

Offline timzim

  • New Egg
  • *
  • *
  • Posts: 11
  • Location: wisconsin
Re: 850 T lay shaft
« Reply #5 on: April 21, 2021, 01:35:58 PM »
The center splines are different (longer) pushing 4th gear into the cas.e. There is also the possibility that my bike built in 11/74 has the T3 type lay shaft since it has an oil filter which seems to be the exception in 850Ts. I sent my lay shaft to harper MG to see if he could match up with something he had in the warehouse. If this doesn't pan out I'm back to square one. I appreciate the response and will post my results

Offline timzim

  • New Egg
  • *
  • *
  • Posts: 11
  • Location: wisconsin
Re: 850 T lay shaft
« Reply #6 on: May 03, 2021, 07:36:40 PM »
Curtis at harper MG came though with a nos lay shaft. The T is a roller today waiting to get the wiring harness installed from Greg Bender, Thanks to all who contribute to this great site most people in my neck of the woods do not know what a moto guzzi is.

Offline Scout63

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2394
  • Location: Orleans, MA USA
Re: 850 T lay shaft
« Reply #7 on: May 03, 2021, 07:48:05 PM »
Good score. Finding the right part is so gratifying.
Ben Zehnder - Orleans, MA USA
46 Rapide
3 Bevel Ducs
71 R75/5
72 Combat Commando
73 v7 Sport project
77 Laverda Jota project
78 SR500
79 G5-T3 mashup
19 Husky Vitpilen


Harper's Moto Guzzi : Go Ride, Break Parts, Call me!
Harper's Moto Guzzi. Where we still answer the phone, use the highest quality parts, and also do Transmission, rear drive, and carb rebuilds fast. Call us at 816.697.3411 and get your problems resolved.
http://www.harpermoto.com
Advertise Here
 


Harper's Moto Guzzi : Go Ride, Break Parts, Call me!
Harper's Moto Guzzi. Where we still answer the phone, use the highest quality parts, and also do Transmission, rear drive, and carb rebuilds fast. Call us at 816.697.3411 and get your problems resolved.
http://www.harpermoto.com
Advertise Here