« previous next »
Pages: [1]   Go Down

Author Topic: 850 T lay shaft  (Read 1546 times)

Offline timzim

  • New Egg
  • *
  • *
  • Posts: 12
  • Location: wisconsin
850 T lay shaft
« on: April 20, 2021, 03:59:57 PM »
Has anyone else had trouble finding a lay shaft for a 850T? My 5th gear is worn and T3s  eldos ect. shafts are all over. I think the T3 shaft would work if I also replaced the dogs and the sliding sleeve, as those part no. are one off as well.
Logged

jwinwi

  • Guest
Re: 850 T lay shaft
« Reply #1 on: April 20, 2021, 05:28:56 PM »
Hey Tim,
Welcome to WG! Somebody with actual knowledge will be along shortly. :boozing:
Logged

Offline Antietam Classic Cycle

  • Gaggle Hero
  • *****
  • *
  • Posts: 14677
  • Happily stuck in the past.
    • Antietam Classic Cycle
  • Location: Rohrersville, Maryland
Re: 850 T lay shaft
« Reply #2 on: April 20, 2021, 05:47:28 PM »
Is it #54 in this illustration that you're looking for?



Logged
Charlie

Offline timzim

  • New Egg
  • *
  • *
  • Posts: 12
  • Location: wisconsin
Re: 850 T lay shaft
« Reply #3 on: April 21, 2021, 10:15:41 AM »
Yes, That's what I need part no.14213611. The part I was sent was actually a 14213612 I believe.
Thanks Tim
Logged

Offline Antietam Classic Cycle

  • Gaggle Hero
  • *****
  • *
  • Posts: 14677
  • Happily stuck in the past.
    • Antietam Classic Cycle
  • Location: Rohrersville, Maryland
Re: 850 T lay shaft
« Reply #4 on: April 21, 2021, 11:15:15 AM »
Any way to tell one from the other at a glance? I have a bin full of 5 spd. munt, may have one.
Logged
Charlie

Offline timzim

  • New Egg
  • *
  • *
  • Posts: 12
  • Location: wisconsin
Re: 850 T lay shaft
« Reply #5 on: April 21, 2021, 01:35:58 PM »
The center splines are different (longer) pushing 4th gear into the cas.e. There is also the possibility that my bike built in 11/74 has the T3 type lay shaft since it has an oil filter which seems to be the exception in 850Ts. I sent my lay shaft to harper MG to see if he could match up with something he had in the warehouse. If this doesn't pan out I'm back to square one. I appreciate the response and will post my results
Logged

Offline timzim

  • New Egg
  • *
  • *
  • Posts: 12
  • Location: wisconsin
Re: 850 T lay shaft
« Reply #6 on: May 03, 2021, 07:36:40 PM »
Curtis at harper MG came though with a nos lay shaft. The T is a roller today waiting to get the wiring harness installed from Greg Bender, Thanks to all who contribute to this great site most people in my neck of the woods do not know what a moto guzzi is.
Logged

Offline Scout63

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 2692
  • Location: Orleans, MA USA
Re: 850 T lay shaft
« Reply #7 on: May 03, 2021, 07:48:05 PM »
Good score. Finding the right part is so gratifying.
Logged
Ben Zehnder - Orleans, MA USA
20 Ounce Stainless Steel Double Insulated Tumbler
Buy a quality tumbler and support the forum at the same time!
Better than a YETI! BPA and Lead free.
Advertise Here
Pages: [1]   Go Up
« previous next »
 


NEW WILDGUZZI PRODUCT - Moto Guzzi Door Mat
Receive donation credit with door mat purchase!
Advertise Here