Author Topic: V700 timing?  (Read 501 times)

Offline Chuck in Indiana

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • Posts: 29445
V700 timing?
« on: October 29, 2021, 10:17:02 AM »
Hi, all.. Andy is putting an engine together for a friend, and just called and asked if I had a degree wheel. "Yeah, I made one when I did the Aero engine conversion." When I asked why, he said there weren't any timing marks on the engine. He told him to take it to Ace Mallot. Of course Ace can do it, but that would be quite a (two) trips for something that simple.
So, anyway, I told him to bring it over and I'd have a look. Is there something that I don't know what I don't know about timing one of these old boogers?  :smiley:
TIA
Chuck in (Elwood) Indiana/sometimes SoCal
 
87 AeroLario
95 Skorpion tour
22 Royal Enfield Classic 3 fiddy
 "Two things are infinite: the universe and human stupidity; and I'm not sure about the universe."
Albert Einstein

Offline guzzisteve

  • Gaggle Hero
  • *****
  • *
  • Posts: 11423
  • "Just Ride It"
Re: V700 timing?
« Reply #1 on: October 29, 2021, 10:59:01 AM »
No timing marks on flywheel cept maybe for crankpin location(arrow).  The marks are on the generator pulley halves on crank. There is 3 bolt holes for mounting them & shims for tension on belt. 4 marks, TDC, static, rpm noted, full advance. This is w/o looking in book. AND marks are on inside half next to arrow on chest cover. I'll be back w/more info.
"Pray through Carlo & your bike shall be healed"
Location: Planet Earth

Offline guzzisteve

  • Gaggle Hero
  • *****
  • *
  • Posts: 11423
  • "Just Ride It"
Re: V700 timing?
« Reply #2 on: October 29, 2021, 11:11:38 AM »
OK, it is for timing left cyl as seen sitting on bike. Marks are like chisel stamps. Looking at pulley from front, 1st on left is TDC, next is 10* at 1200rpm(static), next is 20* at 2200rpm, next 38* at 3600rpm(full advance).
"Pray through Carlo & your bike shall be healed"
Location: Planet Earth

Offline Antietam Classic Cycle

  • Gaggle Hero
  • *****
  • *
  • Posts: 14141
  • Happily stuck in the past.
    • Antietam Classic Cycle
  • Location: Rohrersville, Maryland
Re: V700 timing?
« Reply #3 on: October 29, 2021, 11:14:29 AM »
V700s usually only have one mark - for TDC. I usually swap on an Ambassador back half or just measure and make a static timing mark with a file.
Charlie

Wildguzzi.com

Re: V700 timing?
« Reply #3 on: October 29, 2021, 11:14:29 AM »

Offline guzzisteve

  • Gaggle Hero
  • *****
  • *
  • Posts: 11423
  • "Just Ride It"
Re: V700 timing?
« Reply #4 on: October 29, 2021, 11:15:00 AM »
OR are you talking about marks on cam & crank gears in the front for cam timing?
"Pray through Carlo & your bike shall be healed"
Location: Planet Earth

Offline Tom H

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 3377
  • Location: So. Cal.
Re: V700 timing?
« Reply #5 on: October 29, 2021, 11:26:46 AM »
Charlie is correct. V700 should only have the TDC for LH cyl. stamped into the split pulley. 750 was the first to get the full set of marks and is different than the 850. 750's first mark after TDC is 10 deg, 850 is 5 deg.


EDIT: I think on Benders site there is an article on how to measure the distance for the timing marks.


Tom
« Last Edit: October 29, 2021, 11:37:45 AM by Tom H »
2004 Cali EV Touring
1972 Eldo
1970 Ambo V1000
1973 R75/5 SWB with Toaster
2007 HD Street Bob
1953 Triumph 6T (one day it will be on the road!)

Offline Antietam Classic Cycle

  • Gaggle Hero
  • *****
  • *
  • Posts: 14141
  • Happily stuck in the past.
    • Antietam Classic Cycle
  • Location: Rohrersville, Maryland
Re: V700 timing?
« Reply #6 on: October 29, 2021, 12:28:49 PM »
OR are you talking about marks on cam & crank gears in the front for cam timing?

In that case: https://www.thisoldtractor.com/moto_guzzi_loopframe_timing_gear_replacement.html
Charlie

Offline guzzisteve

  • Gaggle Hero
  • *****
  • *
  • Posts: 11423
  • "Just Ride It"
Re: V700 timing?
« Reply #7 on: October 29, 2021, 12:48:32 PM »
The V700 I'm riding has a pulley w/4 marks cause I like it better, the other 2 have 1 mark for TDC. I may have more pullies in my parts, haven't looked.
Hope Chuck got the info for Andy he needed. Ride On.
"Pray through Carlo & your bike shall be healed"
Location: Planet Earth

Offline Chuck in Indiana

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • Posts: 29445
Re: V700 timing?
« Reply #8 on: October 29, 2021, 03:09:25 PM »
Thanks, guys.. I went to Greg's site, and they won't have to bring it over here after all..:)
Chuck in (Elwood) Indiana/sometimes SoCal
 
87 AeroLario
95 Skorpion tour
22 Royal Enfield Classic 3 fiddy
 "Two things are infinite: the universe and human stupidity; and I'm not sure about the universe."
Albert Einstein

Online chuck peterson

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • Posts: 5209
  • Location: New Haven CT
Re: V700 timing?
« Reply #9 on: October 29, 2021, 05:30:18 PM »
Measure the outside circumference of the gen belt pulley wheel in mm

Divide by 360

Take the result of above and, per steve’s comments

From tdc

Multiple by 10= static mark in mm away from tdc

Multiple by 20 = 2200 rpm. Ditto

Multiple by 38= 3800 rpm full advance. Ditto

Measure along the edge (circumference) of the pulley to make these marks
(if you agree with the stats steve is giving for a v700)






"I'd like to thank all my friends who have kept my Guzzi's going, but mostly...TOMB."
150k on Verts
750 Nevada
400f
R5 Yammie
BV250
4x 1976 Moto Demm Smily,, now 5, oops now 6, oops now 7
1980 SP1000 in little bits and pieces

 

20 Ounce Stainless Steel Double Insulated Tumbler
Buy a quality tumbler and support the forum at the same time!
Better than a YETI! BPA and Lead free.
Advertise Here