Wildguzzi.com

General Category => General Discussion => Topic started by: ponti_33609 on March 21, 2015, 04:07:10 PM

Title: V7 Racer and others - Bar End Mirrors
Post by: ponti_33609 on March 21, 2015, 04:07:10 PM
Hi - I have done a lot of reading of posts and I see what I think is conflicting info.  I have a V7 Racer  being shipped from Moto International in the next few weeks.  The Mrs has strongly urged me to keep this stock-ish.  However on my V11 Sport I really liked my CRG bar ends.  I have read that the V7 have welded bar ends??  Are the folks that have added bar ends.....was it straightforward.... ..?  What specifically have you done to adapt either CRG, Olberon, Risoma or others.  I promised her this is all I would do.   ;)

Regards,
Title: Re: V7 Racer and others - Bar End Mirrors
Post by: ponti33602 on March 21, 2015, 04:35:21 PM
Quote from: pokeyjoe on March 21, 2015, 04:29:25 PM
I had Rizoma's on mine.  They bolt right up and come with the hardware to do it.

Any pics or link I can look at?  We're they welded?



Sent from my iPhone using Tapatalk
Title: Re: V7 Racer and others - Bar End Mirrors
Post by: Moto Fugazzi on March 21, 2015, 05:55:15 PM
Check out this thread from yesterday. http://wildguzzi.com/forum/index.php?topic=75318.0

A search on V7 bar end mirrors here will give you tons of results.
Ken
Title: Re: V7 Racer and others - Bar End Mirrors
Post by: Zinfan on March 21, 2015, 08:48:25 PM
Quote from: Moto Fugazzi on March 21, 2015, 05:55:15 PM
Check out this thread from yesterday. http://wildguzzi.com/forum/index.php?topic=75318.0

A search on V7 bar end mirrors here will give you tons of results.
Ken

As posted in that thread I used Rhino moto bar ends that have a groove that fits the CRG mirrors just fine.

(http://i11.photobucket.com/albums/a189/RickFi/V7/P1000747_zps46d0ccca.jpg) (http://s11.photobucket.com/user/RickFi/media/V7/P1000747_zps46d0ccca.jpg.html)
Title: Re: V7 Racer and others - Bar End Mirrors
Post by: tonUPRacer on March 21, 2015, 09:36:35 PM
Also if you check the product reviews section I did a review with photos of my Rizomas


Sent from my iPad using Tapatalk HD
Title: Re: V7 Racer and others - Bar End Mirrors
Post by: rocker59 on March 21, 2015, 10:06:28 PM
Quote from: Zinfan on March 21, 2015, 08:48:25 PM
As posted in that thread I used Rhino moto bar ends that have a groove that fits the CRG mirrors just fine.

(http://i11.photobucket.com/albums/a189/RickFi/V7/P1000747_zps46d0ccca.jpg) (http://s11.photobucket.com/user/RickFi/media/V7/P1000747_zps46d0ccca.jpg.html)


 ;-T
Title: Re: V7 Racer and others - Bar End Mirrors
Post by: rbm on March 22, 2015, 09:08:18 AM
Whereas most handlebars are completely hollow, Guzzi has welded threaded plate at each end of the V7 bars. These accept M8 screws that secure the barends.  Corsa Italiana sell round barend mirrors that adapt to these fittings -- read the thread referenced earlier.

(https://lh4.googleusercontent.com/-MBu6eroBTJ8/VQ7MkYOAXKI/AAAAAAAAEZA/3wFHxidx7Ak/s800/DSC_0514.jpg)
Title: Re: V7 Racer and others - Bar End Mirrors
Post by: lucydad on March 22, 2015, 11:31:23 AM
Pokey,

Considering bar ends for Mary Anne.  Never tried them.  Visibility as good as stalked type?  Comments?
Title: Re: V7 Racer and others - Bar End Mirrors
Post by: drlapo on March 22, 2015, 01:18:19 PM
what's the problem? just use a different bolt and they bolt right up