Wildguzzi.com

General Category => General Discussion => Topic started by: Spuddy on March 18, 2016, 12:14:09 PM

Title: ROX RISERS ON A STELVIO?
Post by: Spuddy on March 18, 2016, 12:14:09 PM: I'd like a bit of rise and a tad more pull back on Lola's handlebars. So, I'd like to try 1 3/4" adjustable Rox Risers.

Anybody have experience, pics, advice, needed parts list for such an operation?

Spud
Title: Re: ROX RISERS ON A STELVIO?
Post by: radguzzi on March 18, 2016, 12:33:25 PM: I had them on my '09 and liked the rise...

I do not recall the size, I'll see if I can find photos or details of the size.

Multi adjustable in back and forth directions.

Best,
Rob
Title: Re: ROX RISERS ON A STELVIO?
Post by: Demar on March 18, 2016, 01:32:40 PM: http://advrider.com/index.php?threads/moto-guzzi-stelvio-merged-threadfest.113158/page-766#post-28289187
Title: Re: ROX RISERS ON A STELVIO?
Post by: Spuddy on April 07, 2016, 09:36:14 PM: Well, I can't say it was easy or all that hard. But here are the results

Start:

(http://i1147.photobucket.com/albums/o558/paulsmietanka/IMG_2629_zpsg2az9jdr.jpg) (http://s1147.photobucket.com/user/paulsmietanka/media/IMG_2629_zpsg2az9jdr.jpg.html)

Finished:

(http://i1147.photobucket.com/albums/o558/paulsmietanka/IMG_2701_zpsokxzppkp.jpg) (http://s1147.photobucket.com/user/paulsmietanka/media/IMG_2701_zpsokxzppkp.jpg.html)

(http://i1147.photobucket.com/albums/o558/paulsmietanka/IMG_2696_zpsle9xz5vy.jpg) (http://s1147.photobucket.com/user/paulsmietanka/media/IMG_2696_zpsle9xz5vy.jpg.html)

Spud
Title: Re: ROX RISERS ON A STELVIO?
Post by: Spuddy on April 22, 2016, 10:51:37 AM: I'm begining to like these. But I still havta learn not to schunch my shoulders.

Spud
Title: Re: ROX RISERS ON A STELVIO?
Post by: rbond on April 22, 2016, 03:26:51 PM: How hard was re-routing all the cables and wiring? I would like to do the same on my V7C.
Title: Re: ROX RISERS ON A STELVIO?
Post by: Mooney78865 on April 22, 2016, 10:31:35 PM: I have a set on my '16 Stelvio. I believe they are 2". I didn't need to do any mods to the wiring, although I went for the elevation and not to have more pull back. Needed the bars a bit taller to make standing more comfortable for long distance.
Title: Re: ROX RISERS ON A STELVIO?
Post by: Spuddy on April 23, 2016, 02:11:12 PM: Quote
How hard was re-routing all the cables and wiring? I would like to do the same on my V7C.

Not hard but involved. On the Stelvio: lower side faring wings off; tank off; mirrors & hand guards off; handlebars off; controls off; fiddle with wires under triple clamps; hydraulic lines off; if you're careful you can loose only a little fluid, replace new crush washers, pump master cylinders till all tiny bubbles are out. Finally replace controls and figure how to mount risers in such a way to tighten lower clamps under.I mounter risers to bars first. ( I installed 1 3/4" risers which was tight to access the lower Allen head screws.) Good luck.