Vintage Charging Systems / Indicators

[n3303j]

Old Guzzi charging systems:
So here I am 300 miles north of home with a dead battery in the '77 T3.
Turns out the alternator rotor failed (again, open circuit). No sparks = no go. Last one from EME lasted about 45,000 miles. And I bought their premium offering.

So I started thinking about the joys of the permanent magnet rotor in my '98 V11EV. That thing never going to fail. Except back in April the solid state OEM regulator decided to stop regulating. So, instead of no spark I get percolating battery. Guess there is no way to win with charging systems ysing indicator lights.

Just venting here BUT my experiences sure make a case for a VOLTMETER on the dash rather than that dopey red light. Rotor opened mid run so I saw red on startup but indicator gave no clue to depleting battery. Voltmeter would have provided plenty oif warning.

Same with the V11. Red light said nothing about overcharging. Voltmeter would have shown abnormally high voltage at the battery. Gives me something to think about while I await extraction.

Sure makes me appreciate the magneto that was on my '66 R60/2.

[Dirk_S]

Having my own charging issues with my R80 at the moment—first the diode board, and now the regulator. Discovered the battery ground cable was loose, which hopefully explains the regulator failure. I agree about the benefit of a voltmeter. I recently bought a handlebar-mounted USB port that displays the voltage which helped me diagnose my current regulator issue. I’m curious if that voltmeter on the USB port is just as good as a dedicated voltmeter?

This is the one I bought, my second; first one crapped out a bit prematurely, hoping it was a just dud:

EXTRACTME Motorcycle USB Charger, 6.8A Quick Charge 3.0 Dual USB Motorcycle Phone Charger with Voltmeter & ON/Off Switch, Waterproof Quick Disconnect SAE to USB Adapter for Phone, Tablet, GPS - Blue https://a.co/d/7m8vlZG

[wirespokes]

I've carried a spare rotor and diode board on my travels, but never needed them. A friend needed to borrow the rotor once. Of course, that's because I had the tools and parts. It was the clutch cable that broke 20 miles from the US border (I was in Canada heading into NY) that I didn't have a spare. Of course. :-)

I've heard of guys buying a car battery, strapping it to the seat and getting home that way with a dead charging system. I've also heard that with the lights off, you can make it 100 miles before the battery goes flat. Stop and recharge, then go another 100.

[n3303j]

Once rode 125 miles to home on my fully charged Odyssey 925 after the last rotor died. But have no faith that I could make 300 miles and find a charging station en route.

But what really surprises me is the failure rate on these rotors.  It's a really simple winding of reasonably heavy wire. It should last forever. Someone is missing the basics in the engineering or manufacture if this part.

I do spin the engine and am not unhappy running continual 4,500 RPM through the hills.  No problems cruising at 5,000 RPM if wind and loads dictate it. Makes me wonder if the rotor would last longer if kept to an average 3,500 RPM?

[guzzisteve]

I would change supplier for rotor.

[n3303j]

I would change supplier for rotor.

I just did. But I've had really good luck with other EME products. We'll see how the MG Cycle iteratoon holds up.

[Dukedesmo]

Following a recent rotor failure on my '79 LM2, I had it rewound by a local specialist. They tell me it is now better than original and so should last longer.


Time will tell I guess, though if it lasts 46 years like the original did, it won't be me replacing it...   

[chuck peterson]

Making electricians out of bikers since 1929?

[SemperVee]

 FYI - My EV handlebar Voltmeter and cell phone charger -

[n3303j]

I like the mounting. Is it bonded into the Allen screw?
I'm all set for chargers as I put West Marine waterproof units into both bike's side covers.

[SemperVee]

I like the mounting. Is it bonded into the Allen screw?
I'm all set for chargers as I put West Marine waterproof units into both bike's side covers.

picture of specially made bolt and hand made bracket by machinist friend..