Author Topic: Tonti Acceleration Problem  (Read 894 times)

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Tonti Acceleration Problem
« on: November 11, 2026, 11:41:24 AM »
Hi All,

On both my 850 T3 and I-Convert I get a slight hitch when I switch from engine braking deceleration to acceleration. There is also a slight burble in the exhaust note. This all lasts for a fraction of a second then the bike accelerates normally.

As an addition this hitch is most noticeable if I open the throttle slowly. If I open it quickly the engine picks up revs normally. If I stop a slow advance at the hitch point on the flat & level the hitch is almost like I'm missing every second power stroke and may continue fir a few seconds.

Looking for suggestions where to begin my remedy of this issue.

Thanks
« Last Edit: November 13, 2026, 07:34:48 AM by n3303j »
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Tonti Acceleration Problem
« Reply #1 on: November 13, 2026, 07:38:56 AM »
Figured jets and needles and throttle slides would draw almost as much attention as a good oil thread. Guess I was wrong. Maybe they all do it? Still looking for a path guided by the carburetor gurus.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Offline pressureangle

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 1036
  • '97 1100 Sport i, '89 Mille GT
Re: Tonti Acceleration Problem
« Reply #2 on: November 13, 2026, 07:42:41 AM »
Give us a chance, man- 24 hours at least, gotta weigh the damage to follow.

This is difficult to diagnose without experiencing it, but my guess is slides. You have accelerator pumps, yes? If so that's probably why it doesn't happen when you open the throttle farther.
Depending on where the issue is, you might try raising the needles a clip, but they may be too high in the curve to affect an off-idle stumble.
Do you have anything other than stock airbox?
Something wistful and amusing, yet poignant.

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Tonti Acceleration Problem
« Reply #3 on: November 13, 2026, 07:52:50 AM »
44 quiet hours elapsed.

But stock airbox on both the T3 and Convert.

T3 stock exhaust.

Convert at 14K original miles.
Convert; previous owner bashed most of the baffles out of the muffler. Stock diameter exit hole remains. Have not yet checked jetting.

T3 at 130K original miles. Jets replaced at 100K miles. Carb slides replaced to cure unstable idle condition at 115K miles.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Offline Groover

  • Gaggle Hero
  • *****
  • Posts: 2951
  • If it ain't broke, I'll break it.
    • Scooteropolis
  • Location: Columbus, Ohio
Re: Tonti Acceleration Problem
« Reply #4 on: November 13, 2026, 08:26:09 AM »
My target area would be the low end needle valve, maybe turn it in (to lean it) perhaps 1/4 of a turn on each side and see if that helps. Sounds to me it's "loading" a bit while engine braking. Or maybe 1/8 of a turn at a time.
« Last Edit: November 13, 2026, 08:42:35 AM by Groover »
1981 Moto Guzzi V1000G5
1987 Moto Guzzi LM1000SE, a
1987 Moto Guzzi LM1000SE, b
1980 Piaggio Vespa P200E
1980 Piaggio Vespa P125X
1980 Vespa Grande Moped
1980 Vespa SI Moped
http://scooteropolis.com/

Offline nc43bsa

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 1506
  • Location: Mooresville NC
Re: Tonti Acceleration Problem
« Reply #5 on: November 13, 2026, 09:28:26 AM »
I'd try changing the mixture screw a 1/4 turn.
1990 MilleGT

Offline wirespokes

  • Gaggle Hero
  • *****
  • Posts: 2452
Re: Tonti Acceleration Problem
« Reply #6 on: November 13, 2026, 11:07:49 AM »
I'm with Groover on this. Decelerating brings on an over-rich mixture. The carb doesn't know that less fuel is needed than when accelerating. So then you open the throttle suddenly and it takes a bit for the mixture to normalize. In stock car racing they go to great lengths to get the mixture right. When they decelerate, those cars pop and spit and backfire due to the lean mixture. Street cars are given a 'fatter' mixture to prevent that - people don't want their cars popping and spitting on deceleration. So unless you're backfiring on decel, it's definitely a rich condition.

Frankly, I'd think it wiser to be smoother on the throttle.

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Tonti Acceleration Problem
« Reply #7 on: November 13, 2026, 12:03:53 PM »
Actually I make a point of being gentle and smooth on the throttle. At 81 I no longer have anything to prove while riding. I enjoy smooth and quiet and look forward to more of the same.

I'll try a tweak of the idle mixture screw when the weather gets a bit more suitable.

This burble is not dependent on speed. It will happen when changing from deceleration to acceleration whether I'm doing 15 or 45 even on a very slow advance on the throttle. If I advance very slowly I can extend the amount of time this disruption continues.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Online pehayes

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 4811
    • Falcone Touring
Re: Tonti Acceleration Problem
« Reply #8 on: November 13, 2026, 12:32:51 PM »
I spent years chasing something similar on an SPII.  It didn't happen on all throttle changes.  Just happened when pulling off the line after a red light.  Enough of a hiccup that I feared getting rear ended.  By other reasons I eventually discovered that it was a very weak COIL.  I could sit at a light at idle just fine.  Start to accelerate and it had a good miss before building speed.  The very weak spark was able to spark and burn idle fuel.  However, that same weak spark was challenged by the suddenly enriched acceleration mixture.  Changed a coil and never looked back.  YMMV.

PS:  The only way I found it was that the weak coil eventually failed completely and that one side stopped sparking altogether.  I was always testing spark by pulling the plugs and looking for visual spark.  Turns out that it takes far less amperage to create a spark in standard atmosphere than to try and create the very same spark under increased air pressure (think combustion chamber).

Patrick Hayes
Fremont CA

Offline Tony F

  • Gosling
  • ***
  • Posts: 104
  • Location: Christchurch New Zealand
Re: Tonti Acceleration Problem
« Reply #9 on: November 13, 2026, 03:54:10 PM »
It sounds to me like the bike has a lean spot just off idle. I had the same issue on with the Mikuni flatslide carbs on my LM engined SP1000.

The slide cutaway is the key here. I filed 0.5mm from the bottom of the slides effectively reducing the cutaway height and 90% cured the issue. I could have gone back in and filed some more material off the slide but thought it might be too easy to overdo it. (I do need to attribute this hack to one P Roper esq!) You could try some slides with a smaller cutaway if you could buy or borrow some.

This assumes that ignition timing, valve clearances and carb balance are all spot on.

Good luck.
Tony
'79 SP1000
KTM Duke 890R
MV Agusta F4 (x2)

Offline wirespokes

  • Gaggle Hero
  • *****
  • Posts: 2452
Re: Tonti Acceleration Problem
« Reply #10 on: November 14, 2026, 11:43:30 AM »
PS:  The only way I found it was that the weak coil eventually failed completely and that one side stopped sparking altogether.  I was always testing spark by pulling the plugs and looking for visual spark.  Turns out that it takes far less amperage to create a spark in standard atmosphere than to try and create the very same spark under increased air pressure (think combustion chamber).

I'll second that! Just recently I found a bad connection between the stator and regulator on the G5. It's got the EME upgraded permanent magnet alternator. I thought the bike ran fine before but now there's a noticeable improvement - stronger and better acceleration. It doesn't seem logical the coil has to work harder creating a spark under compression or with a richer mixture, as compared to out in the open, but it definitely is the case.

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Tonti Acceleration Problem
« Reply #11 on: November 14, 2026, 11:49:51 AM »
Small aircraft sparkplugs are bench tested at 125 psi because pressure does effect the spark.

A long time ago when garages used to clean spark plugs I remember seeing the plug test machine at my local shop. It put the plug tip into a pressurized chamber. There was a mirror that showed the tip through a sight glass and a coil that delivered repetitive sparks. Install the plug, push the button & watch the spark.

All back when parts cost way more than labor.
.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Offline Stretch

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 794
  • Location: Belgrade, Maine
Re: Tonti Acceleration Problem
« Reply #12 on: November 14, 2026, 11:55:23 AM »
Is it worse when hot? Or cold?

                      -Stretch
1967? Change Jiang M1M
1978 Yamaha SR500
1971 BMW R75/5
1987 BMW K75S
2011 Kawasaki KLR650
2011 Triumph Rocket III Touring
2015 Triumph Trophy
2017 Moto Guzzi 1400 California Touring

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Tonti Acceleration Problem
« Reply #13 on: November 14, 2026, 11:58:38 AM »
Is it worse when hot? Or cold?

                      -Stretch
It's apparent constantly after warmup. But it's never bad, just not right.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Offline Stretch

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 794
  • Location: Belgrade, Maine
Re: Tonti Acceleration Problem
« Reply #14 on: November 14, 2026, 12:32:25 PM »
Could be coil.

A failing coil will work, but it gets worse as it gets hot.
Sometimes works perfectly when cold, so the bike will
start with no trouble 1st thing.

Trouble starting when hot?

Coil okay? (Swap for known good one?)

Then maybe pilot jet/screw, needle or slide cutaway, or
worn slide/carb body.

I once had a Grand Marquis with the early throttle body fuel injection
that had a similar problem. I never got to the bottom of it, although
periodically a new distributor cap seemed to help.

Got nothin' else for ya, man......

                                                    -Stretch

1967? Change Jiang M1M
1978 Yamaha SR500
1971 BMW R75/5
1987 BMW K75S
2011 Kawasaki KLR650
2011 Triumph Rocket III Touring
2015 Triumph Trophy
2017 Moto Guzzi 1400 California Touring

Online Michael_A

  • Hatchling
  • **
  • *
  • Posts: 81
    • Penguin Video Productions
  • Location: Out in the west part of Texas...
Re: Tonti Acceleration Problem
« Reply #15 on: November 14, 2026, 05:25:34 PM »
There's a saying, 90% of carburetor problems are ignition. Pretty easy and cheap to try new leads, plugs, and even coils. Points would be suspect, too, but not sure if they are fitted on yours. I'd check and refurbish everything in the ignition system. At times it can be really hard to isolate any of these components because they may work well when cold and get progressively worse when hot. Sometimes. So much easier when they just take a dump and stay that way. Back to the carbs, kinda sounds like (if it has them) accelerator pumps... maybe a holy diaphragm or partial blockage due to dirt? 
« Last Edit: November 14, 2026, 05:27:47 PM by Michael_A »

Online chuck peterson

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 5540
  • Location: New Haven CT
Re: Tonti Acceleration Problem
« Reply #16 on: November 15, 2026, 06:37:56 AM »
Too much slack in the throttle cables..?

Hmmmm. Maybe, just thinking. Might be simple to try
"I'd like to thank all my friends who have kept my Guzzi's going, but mostly...TOMB."
150k on Verts
750 Nevada
400f
R5 Yammie
BV250
4x 1976 Moto Demm Smily,, now 5, oops now 6, oops now 7
1980 SP1000 in little bits and pieces

Offline Fontain25

  • Gosling
  • ***
  • Posts: 136
  • Location: Illinois USA
Re: Tonti Acceleration Problem
« Reply #17 on: November 20, 2026, 06:51:17 PM »
Does it have a good idle on both cylinders?

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Tonti Acceleration Problem
« Reply #18 on: November 20, 2026, 07:12:41 PM »
Does it have a good idle on both cylinders?
CONVERT:  Idles okay but I'm going to go through all systems before asking for more suggestions.
Compression 170# both sides
14,500 total miles (I think it might be correct).
#60 Slides BUT running WAY too rich 25 MPG! And black plugs.
In process of pulling carbs to check all jets and install new air filter.
Waiting for gaskets to check rocker clearance.
I'll return all to factory recommendations and see where I'm at.
Bike "new to me". About time we became intimate.

T3: There is no hesitation in cold fall air. Warm weather air would make it slightly richer. So next step would be to run it slightly leaner. But where it's running fine this time of year it will be the "rider" while the Convert becomes the "patient".

Thanks all, I'll keep you posted with the resolution.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Offline Tony F

  • Gosling
  • ***
  • Posts: 104
  • Location: Christchurch New Zealand
Re: Tonti Acceleration Problem
« Reply #19 on: November 21, 2026, 01:56:56 AM »
Have you got a copy of the Dellorto tuning manual? Its well worth having, you should be able to find a copy online. The following clip shows the relavent carb circuts for various throttle opennings which might help you narrow down your issues.



Tony
'79 SP1000
KTM Duke 890R
MV Agusta F4 (x2)

 

*IMPROVED* - Wildguzzi Amazon Affiliate Storefront!
Proceeds go back into the forum.
If you need to buy it anyway, use the affiliate link to help the forum.
Advertise Here