Wildguzzi.com
General Category => General Discussion => Topic started by: lazlokovacs on February 17, 2018, 07:27:16 PM
-
my mates Cal Vintage... In pretty immaculate condition... has developed a strange fault.
After around three minutes of riding when started from cold it pretty much ALWAYS cuts out. Loses both cylinders at once.
Sometimes its then hard to restart. A quick roadside test showed that when it won't restart there is no spark at the plugs. (the non sparking plug worked fine on my bike)
Weird thing is the batt has plenty of juice, it turns the starter motor over beautifully... And weirder still, once the bikes warmed up it gives no trouble at all.
Any ideas?
cheers
-
The bike is telling you it wants to be sold cheaply.
-
Does it restart after a brief rest then fine? I had an electronic ignition in my Ariel for about 5 years and it started doing this. Never figured it out for sure, but think it was the coil.
-
my mates Cal Vintage... In pretty immaculate condition...
Any ideas?
cheers
are the battery terminals clean and tight?
how many miles? some of the Vintages just never ran right.. some solutions were to change up the ECU for a V11 box (5M?) I have friend who's Vintage was so bad he got a lemon law replacement NEW bike..
is there any way you could substitute another ECU?
I know it's a little off the wall answer.
-
Sidestand switch?
-
Both cylinders at EXACTLY the same time ?
-
are you near the Black Hills, Burkittsville, Maryland? :shocked:
(http://thumb.ibb.co/i0wtQn/p22546_p_v8_ag.jpg) (http://ibb.co/i0wtQn)
-
listen for the fuel pump upon restart attempt.
then check to see if the fuses are clean and making good contact.
-
My similarly spooky Burkittsville Cali was fixed by pulling away the fuse/relay assembly and finding and re-insulating a wire that was shorting against the assembly's bracket. While in there I replaced and DeoxIT'ed the fuse and relay sockets and cleaned up the spades with 0000 steel wool. Not a stumble since.
(http://thumb.ibb.co/cHy4y7/IMG_0080.jpg) (http://ibb.co/cHy4y7)
-
Sounds like something when getting up to temperature is then failing
So just ask the question again definitely BOTH sides loose spark?
4 Spark plugs, 2 coils? I'm asking as that is what Carl Allison's diagram shows
If I'm using the correct diagram I'd look at the Power Relay and check Fuse 7, swap the relay with something else and check all the fuse contacts. Loss of power or the relay misbehaving will stop the bike dead, it supplies the injectors and coils. I'm not saying that is the fault but it's a common failure point so it's where I'd start
John
-
I had the same problem on a 08 Calvin. We would be going down the road just fine and all of a sudden it would quite sometime it would pick up by it's self other times not. Cleaned the fuses and replaced relays, but no enchilada.
Turned out there was a bad connection behind the relay holders.
Removed the relay block and let it hang down and pulled out the wiring.
Turned the ignition on and just kept wiggling the connectors in the harness until I could hear the fuel pump start and stop.
Squeezed the connector and put it all back and all was well for seven years, but last summer the cutout was back, so I will have do it again this spring.
I did put a V11 ECU in it and it runs like it should now.
Good luck with yours.
Earl
-
One more idea: I had he same thing happen to me on the same model bike. Turned out it was a short in the wires under the seat. Take off the seat and see if anything has worn bare or come loose from the pressure of sitting on the seat.
-
Another place to check is the base of the ignition switch. The contacts could be loosing their connection. It can be removed and cleaned or replaced. It is a wear part that can be replaced . It comes as the base with about six inches of lead and its connection to the harness. You don't need to remove the switch, just gain access to the base. I'll post the part number when I get to the shop unless someone beats me to it. The most likely culprit is the sidestand kill switch as Pete said.
-
Thanks guys,
Huzo - My mate says that he THINKS its both cylinders cutting out at the same time... I haven't ridden it so I can't be 100percent sure
Pete- sidestand switch has been previously welded shut, and there's nothing random about when the bike loses power..... happens after about 3mins every time!
OLDjock---- Yes, its 4 plugs 2 coils and I'm sure you have the right diagram.
Fuel pump is working fine.
I'm thinking its going to be a case of inspecting and testing all the wires...
Will start at the relays then
Anyone have a part number for a replacement relay? (or even better the non-guzzi equivalent part number)
Interestingly, my friend also says that if he opens er right up when it starts to cut out then he can kind of ride it out and the bike will keep going. Until next time he drops the revs....
head-scratching.
-
Electric petcock fault?
-
A pilot would not stand for the sort of engine.
-
Thanks guys,
Huzo - My mate says that he THINKS its both cylinders cutting out at the same time... I haven't ridden it so I can't be 100percent sure
Ok.
I would start my investigation by starting the bike and invite it to fail.
When it cuts out I would ascertain if it's on both cylinders at EXACTLY the same time.
Thinking about it a bit suggests it can't be coil, points, electronic ignition pickup or similar, because there'd be a tendency to struggle on with one cylinder firing.
It's something that serves both pots.
My MV Augusta had a feature in the ECU that supplied a fast idle for 20,000 spark cycles which translates to about 4 minutes fast idle then the brain switched the idle speed back to 1100 rpm.
Just wondering (showing my ignorance) is your bike fuel injected with ECU controlling things ?
Maybe there's a switching function that reads engine temp and giving a false command ???
You must ascertain if it's fuel or not.
You'd reckon that a fuel starvation issue or tank vent problem would not kill both at once with such suddenness.
-
are the battery terminals clean and tight?
how many miles? some of the Vintages just never ran right.. some solutions were to change up the ECU for a V11 box (5M?) I have friend who's Vintage was so bad he got a lemon law replacement NEW bike..
is there any way you could substitute another ECU?
I know it's a little off the wall answer.
No it's not.
Substituting a known good unit on yours and putting the suspect one on the other bike gives a non ambiguous answer.
Always a good diagnostic approach.
-
A pilot would not stand for the sort of engine.
Well no...
But this bloke is not exactly thrilled to bits either !
-
are the relays Siemens? (bad) get a full set from Pyro Dan
http://dpguzzi.com/
are there fault codes stored? I think you need Guzzidiag software to read them..
-
I’m just throwing something out not from experience. Could the map be sent to a mapping specialist for reviewing. We have a couple of those guys on the forum.
-
Lazlo , it is really hard to diagnose problems long distance , and doubly hard when the questions and answers are being filtered thru a third person . Any chance your friend could simply join the board so our experts can communicate directly with him ?
Dusty
-
I�m just throwing something out not from experience. Could the map be sent to a mapping specialist for reviewing. We have a couple of those guys on the forum.
Map?
-
If either the ECU relay (52) or the power relay (50) drops out the bike will stop.
A small wire wrapped around the 87 pin of each relay going to a 12 Volt lamp to chassis will indicate which relay is dropping (the ECU will cause both to drop)
The lamp will glow as long as it has power, if it goes out when the engine stops then find out why.
Chassis ----------------(12V Lamp)-----------------> 87 pin
Important Clue - The ECU relay coil is grounded through a diode the wire also grounds the Start Relay coil. Does the bike crank over after it stalls?
A bad timing sensor will cause the power relay to drop out, they have been known to fail with temperature (turns of ignition injectors and pump), the lamp on the 87 pin of that relay will tell you if that's happening.
One more thing it could be is tank suck with a blocked tank vent the vacuum prevents the pump drawing fuel out of the tank, somehow I don't think its that in this case but it's dead easy to check, just oren the fillet cap to see if you get an inrush of air and immediate restart.
http://www.thisoldtractor.com/guzzi007/schematics/2008_California_Vintage.gif
-
Having been a victim of tank suck, I believe that it can be ruled out in this case. Tank suck is not partial to any given amount of set time. It will vary with how much fuel is in the tank. Tank suck will occur sooner on a full tank than a more empty one. Also, if the tank is then not vented, it will occur a bit further down the road.
As for a switch, I only thinking out loud here, but again, if a loose connection, why would it only happen 3 minutes into the engine running and not happen again later on? Certainly not ruling out the electrical aspect here. Just thinking it is unlikely the ignition switch or something loose. Loose would more translate to "Whenever I hit some bumps, the bike cuts out", which is not what was described here. Since there seems to be a defined pattern here, that should be a little more helpful in figuring it out.
John Henry
-
Kiwi Roy-
great info
bike cranks over just fine after it stalls.....
-
I had a sensor fail on a 97 Cal.
-
I took one of Carl's drawings and cut out the vital organs to illustrate how simple they are. All of the wiring you see is like a sub loom, very reliable, all it needs is a signal to go from the ignition switch via a stand relay and the kill switch. The wire going to the tach is not important for running.
The Safety diode on the Vintage must be grounded thru pin 2 for the ECU relay to close, most other Guzzis have the diode straight to negative with the interlocks in the signal from ignition switch.
The relay pins are the easiest point to access the signals, just wrap a small wire around the pin.
(http://image.ibb.co/er4WD7/Heart_of_a_Guzzi.jpg)
TKelly just mentioned a sensor, if the timing sensor goes open circuit the ECU will think the engine has stoped and drop out the power relay. These sensors are known to fail and also leak oil. They must be gapped correctly. The lamps I show will tell you if the sensor is not working the ECU lamp will be On but the Power Relay lamp will not turn on while cranking.
I think I'm the only owner that put a lamp on every relay of my first fuel injected Guzzi, I'm an electrician but I can't see electricity without some help LOL
-
TKelly just mentioned a sensor, if the timing sensor goes open circuit the ECU will think the engine has stoped and drop out the power relay. These sensors are known to fail and also leak oil. They must be gapped correctly. The lamps I show will tell you if the sensor is not working the ECU lamp will be On but the Power Relay lamp will not turn on while cranking.
I think I'm the only owner that put a lamp on every relay of my first fuel injected Guzzi, I'm an electrician but I can't see electricity without some help LOL
some Spine frame had a problem with the cam sensor, the wire out of the sensor made a 90 degree turn up, when the engine warmed the signal would fail.(and the wire would be soft and flexible in the area). so wondering if it happens regularly when the engine warms up enough to affect the sensor wire?
-
some Spine frame had a problem with the cam sensor, the wire out of the sensor made a 90 degree turn up, when the engine warmed the signal would fail.(and the wire would be soft and flexible in the area). so wondering if it happens regularly when the engine warms up enough to affect the sensor wire?
What you say makes perfect sense but the sensor is expensive just to change on spec.
If the Power relay drops out while the ECU relay stays closed it would certainly point to the sensor, so easy to verify, so hard to persuade the owner to do a little testing
-
The sensor is not expensive if you don't buy the part from Guzzi.
http://www.miparts.com/detail/rpm-sensor-engine-management_15598#.WotM7qinGUm (http://www.miparts.com/detail/rpm-sensor-engine-management_15598#.WotM7qinGUm)
Also available on ebay from England for about $30-40.
-
Kiwi Roy you are a gentleman and a scholar!!!
thank you so much for your help...
due to work commitments it will be a few days until I can work on the bike, will let you know the outcome.
Antmanbee that sounds very plausible too thank you....
-
I had this happen to me on a trip. Temps in the 90s (unusual for Carmacks, YT). Sheets of rain. Humidity past 100%. I pulled into a gas stop, filled up, got some crap from a "biker" and decided I wanted to get some distance between him and me. So I flogged it out of the driveway and up the highway. Less than a mile down the road the bike simply died. Like yours. I managed to pull into a road maintenance gravel pit (out of sight of the road) and went down the basics. Nothing obviously amiss, so I punched the button and off I went. No stumbles -- ran perfectly. Things were perfect until the next gas stop, where except for the harassment, I repeated the previous incident. This time I went after the relays. When I went to pull them out for the mix-n-match, the fuel pump relay cap came off and water poured out. I didn't like that, and my spares were also Siemens. I went to the abandoned Ford SUV in the gravel pit and pulled its unlabeled relays, replacing all of my OEMS with stuff from the stuffed Ford. I didn't have any Vaseline with me so I dressed the contacts with Chap Stick. Later I glued a piece of inner tube over the fuse and relay block. The Ford relays are still in there after 10+ years, and I've had no further incidents.
-
The sensor is not expensive if you don't buy the part from Guzzi.
http://www.miparts.com/detail/rpm-sensor-engine-management_15598#.WotM7qinGUm (http://www.miparts.com/detail/rpm-sensor-engine-management_15598#.WotM7qinGUm)
Also available on ebay from England for about $30-40.
Wow, I thought I would easily find a compatible Auto product, I ended up getting one off an MV Augusta from a Dutch vendor.
I don't normally like putting Chinese parts on my Guzzi but in this case it's such a simple device pretty hard for them to screw up.
Thanks for the source :thumb:
-
I use a lot of Chinese parts on my Guzzi and have had good luck and been impressed with most.
I think there is a lot of unwarranted prejudice against Chinese manufactured parts like there used to be for Japanese parts in the 60s and 70s.
-
Hello Everybody.
I am the aforementioned friend of 'lazlokovacs' and owner of the naughty Cali vintage.
Thank you all very much for your input in helping solve my issue.
Below is a list of changes I have made, in chronological order
The bike is behaving a lot better, It starts everytime now and loosing spark less but still is loosing spark on occasion and always in the first 5 minutes of riding, If I keep it alive after 5 minutes of riding it is always well behaved and nothing unusual, very head scratching...
So far I have...
*checked battery. no issues
*fitted new NGK spark plugs and caps. This didn't make much difference
*checked side stand switch. no issues
*checked RPM sensor. no issues
*tried running bike with disconnected temperature sensor. made no difference
*checked all fuses, and replaced entire set of relays (ordered gutsibits' standard set of relays, not sure of the brand). This has made a noticeable difference though strangely not solved the issue completely.. maybe the terminals that the relays slot into need a clean?? Any other ideas given this information?
Thanks again everybody.
My first post!
Elv
-
Hello Everybody.
I am the aforementioned friend of 'lazlokovacs' and owner of the naughty Cali vintage.
Thank you all very much for your input in helping solve my issue.
Below is a list of changes I have made, in chronological order
The bike is behaving a lot better, It starts everytime now and loosing spark less but still is loosing spark on occasion and always in the first 5 minutes of riding, If I keep it alive after 5 minutes of riding it is always well behaved and nothing unusual, very head scratching...
So far I have...
*checked battery. no issues
*fitted new NGK spark plugs and caps. This didn't make much difference
*checked side stand switch. no issues
*checked RPM sensor. no issues
*tried running bike with disconnected temperature sensor. made no difference
*checked all fuses, and replaced entire set of relays (ordered gutsibits' standard set of relays, not sure of the brand). This has made a noticeable difference though strangely not solved the issue completely.. maybe the terminals that the relays slot into need a clean?? Any other ideas given this information?
Thanks again everybody.
My first post!
Elv
Nowhere near Epsom/Surrey are you ?
-
Welcome to WG Elvis .
Dusty
-
Welcome Elvis,
Did you ever try to determine if one of the relays was dropping out as back in reply 23?
Knowing if one or both of the relays is dropping out will give us a vital clue.
Use a length of 20 gauge or finer wire wrapped around the relay 87 pin, small 12V lamp to ground.
When you turn the key On both lamps will light
3 or 4 seconds later the second one will go out,
when you press start button the second light should come on again and stay alight as long as the bike's running.
Other
Look in each of the relay bases, poke each contact to make sure it doesn't push out the back.
-
kiwi roy,
Elvis and I will perform the lamp test tomorrow...
Interestingly, today the headlight fuse blew completely, the fog lights and accessories outlet stopped working (although the corresponding fuse was good) and the key switch fuse looked burnt but not totally out.
hmmm
-
Interestingly, today the headlight fuse blew completely, Do you mean Fuse 3?
Its possible it was just a fluke or I would be looking for a short possibly in the brake light, i wouldn't worry unless it happens again.
http://www.thisoldtractor.com/guzzi007/schematics/2008_California_Vintage.gif
the fog lights and accessories outlet stopped working (although the corresponding fuse was good) and the key switch fuse looked burnt but not totally out. Although the fog lights and accessory socket is powered from Fuse 5 the relay coil (33) is fed from the headlight fuse, if that's out the fog lights will be off, interesting the accessory socket is shown to work when the Fog lights are NOT, I would have expected it to come on the same time as fog lights, perhaps the relay is one of those with two 87 contacts not an 87/87a
Prepare to leave the little lamps in place as long as it takes for the trouble to surface again, just tuck them somewhere out of the way that you can see if need be.
Good Luck
-
yep fuse 3
also, I tried your test but when I connect pin 87 to ground via a multimeter (i dont have a test light) from the pump relay it causes the pump to activate for as long as i maintain ground... is this normal?
-
my bad....
the multimeter is no substitute for the test light as it doesnt have any load.... right???
-
Are you sure you are grounding 87, that doesn't make sense it would cause the fuse to blow
If you ground 86 of the pump relay it will make the pump go.
Yes, the multimeter has it's uses but a small lamp is much more practical for this test.
You cannot hold the multimeter in place while riding, a light can be just fixed in place and forgotten until it's needed.
Do you have an electronics parts store nearby where you can purchase some small 12 Volt lamps, another option is to make a couple of lamps using LEDs and 1000-2000 Ohm resistors
The lamp on the 87 contact will not change the relay's state, just tell you what it is.
I'll send you a PM
-
hey kiwiroy,
I had a good look at elvis's bike today... annoyingly the wires going to and from the pump and ecu relays are completely different colours than shown in the manual. the other relays and fuses are correct as per the manual.
The loom has 100per cent verifiably not been touched since the bike was new...
not an insurmountable problem, but.... challenging
just to be clear the pump relay is far right with the ecu relay next along yes?
and pin 87 is in the middle of the relay yes?
relay looks like this right?;
I
I <this one is 87
- -
cheers
-
I believe you are correct, 30 and 87 are full size spade connectors.
It is possible your bikes may use a different relay than we do but the pin numbers should be standard.
Give me the part No if you see one and I will check
I normally draw them like so
------ 30 Always alive
------ 87 normally open, the load connects to this one
| | | 65, 87a, 66 65-66 should read ~120 Ohms (maybe backwards)
30 to 87a will read zero Ohms
What's the plan?
-
Yesterday Lazlo made some testlights to connect to the relay and we did KiwiRoys test (Thank you Kiwi_Roy!)
some interesting things happened...
(http://thumb.ibb.co/iYaa2n/guzzi1.jpg) (http://ibb.co/iYaa2n)
(http://thumb.ibb.co/j4Djv7/guzzi2.jpg) (http://ibb.co/j4Djv7)
1. I turn the key on, ECU/on Pump/on for 1 second and then off, like normal
2. I press the starter ECU/on Pump/on
3. after a 2-4 minutes, predictably, the bike looses the odd spark but just about stays alive, while this is happening both ECU and 4. Pump light stay strong
5. after another minute of missing spark and backfiring the bike does cut out, lights read ECU/on Pump/off AND interestingly the red oil light on the dash flickers uncertainly for a few seconds before then deciding to stay on.
6. I turn key off
7.I turn the key on, ECU/on Pump/on for 1 second and then off, like normal
8. this time the bike does not start again. I leave it for about 3 minutes and try again and it starts up fine.
So, many strange things happening.
The one thing that is the most head scratching to me is that this consistently happens around the 2-4 minute mark, If it manages to stay alive past this, it operates absolutely fine and never misses a spark... is something being affected by the bike not being warm yet? Does the ECU send different information pre and post the bike warming up? The cables on the bike look in great condition so I am sceptical of the bike shorting out because of a frayed wire, as then why would cut out after 2-4 minutes and not afterwards? thinking out loud now :)
Thanks for everyones replies!
Elv
-
That's great information, not sure what it means exactly but it's eliminated the wiring.
Actually I'm starting to lean towards the RPM sensor or timing sensor, its opening up as it heats up then perhaps closes again once really hot.
This sensor is just a coil of wire wound over a magnet, quite often I have seen coils corroding off or breaking off where they are soldered to the wires.
This sensor is common to both left and right cylinders so it probably effects both sides similarly. You may be able to catch it with your Ohmmeter, the normal is about 680 Ohms
The pump relay doesn't drop out straight away it has to miss a number of pulses but the ignition and injectors have to see every pulse or they will get out of kilter.
Do you have another similar bike you can borrow the sensor off while you order a couple of the sensors Antmanbee showed us in reply 30
What do you think of the lights idea now?
-
http://www.dpguzzi.com/efiman.pdf This document is a good tutorial on the Fuel Injection, don't worry that it's old it still applies.
Note the gap 0.6 - 1.2mm, i usually stick a blob of wax or glue on the end then measure it once it's impressed by the wheel.
And one last thing, the sensor cable is only about a foot long so find the connector 1,2,3 buried under the tank snd make sure the contacts in there are in good shape.
-
Roy, there wouldn't be an electrolytic cap.in the ECU which heats up, fails, then self repairs enough to be able to carry on? :undecided:
Used to have the odd problem in early ham radio sets sometimes. Intermittent faults can be a real swine to track down sometimes. :evil:
-
Roy, there wouldn't be an electrolytic cap.in the ECU which heats up, fails, then self repairs enough to be able to carry on? :undecided:
Used to have the odd problem in early ham radio sets sometimes. Intermittent faults can be a real swine to track down sometimes. :evil:
I hope not the chances of finding something like that are pretty slim.
The way it started backfiring with no loss of relay pointed to the ECU loosing track of the phonic wheel and firing at the wrong time something that fits right into a failed sensor
if that doesn't fix it the next step would be the ECU so hopefully it's just the inexpensive sensor.
If you think about how vital the sensor is why not have a spare, I tried to find an auto equivalent around here, impossible
http://www.miparts.com/detail/rpm-sensor-engine-management_15598#.WotM7qinGUm From Antmanbee
-
I have ordered a RPM sensor, cheapest one i could find was on Amazon...
https://www.amazon.co.uk/gp/product/B00D76FWF2/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
Lazlo is bringing me a spare ECU in a few days just incase the new sensor doesn't do the trick.
:thumb:
-
I changed over the RPM sensor with a brand new one and have been riding about 2 weeks with no problems.
It seems to have fixed the problem, THANK YOU everyone for your suggestions.
Just for my education...
Is anyone able to explain why the previous RPM sensor was only having trouble in the first few minutes of starting the bike though?
-
^^^^^
No. :smiley:
Ron has a similar "weird" issue.. that may or may not be cured by the phase sensor. Some of this stuff is not to be understood. <shrug>