Visit the Wildguzzi Amazon Affiliate Store
Tips:This adjustment reminds me that I need to get a proper valve adjustment tool to hold the valves when tightening the nut. I've always just used a pair of pliers, but it's too easy to allow it to nudge just slightly and then I have to loosen the nut again, readjust, tighten again. If anyone has a suggestion of a better way to hold the adjuster tab I'm all ears.Z
Kev, does the hemi head make it more awkward to adjust the valve clearances? I don't recall having to use pliers on the Heron setup.
My main "hunting" knife is a Frost laminated steel jobbie. A story behind how I got it but over the years it has cut through hundeds of rabbit bones and has been given a quick tickle up twice. A beautiful knife.
Motion Pro makes a tool for that-of course they do!
a tool came in the 1972 Eldorado kit. mine got lost somewhere but if you can still find a pack of ignition wrenches one will fit. otherwise long nose vice grips.
Why are you guys discussing knives in the middle of a First Service thread??
Not at all.How do you hold the adjuster from turning when you tighten the locknut?!?
I have a terrible bad habit of confusing my bikes but if I remember correctly I used a small Allen wrench to hold the adjuster in place while I tightened the nut. But I could be remembering the Norge or agree so. I've done them five or six times but the V7 stornello only once.
I don't recall ever seeing a Guzzi with an Allen head valve adjuster. The four valve Carcs or Cali?!?
How do you hold the adjuster from turning when you tighten the locknut?!?
Now ya got me Kev. I can't remember. (More )The problem is, I can't remember what is on the top of them now. I know I don't use pliers. I was thinking they were slotted, hence screwdriver. If they are not and are square it would be either my mag spanners or the little square Honda tappet holder, which is basically a small deep socket with a handle on it.With the Breva, if the clearance is out by even a couple of thou then it has quite a loud tick. I gave up having a regular service schedule for the valves because I couldn't see the sense of the possibility of damaging the gaskets simply to take up one thou on one valve. Now I do them when the tick tells me to, which is very rare indeed.
Lol, the adjuster screw has a thin raised lip/tab across the center, like the negative of a flat-head slot.
I found it! I have an aluminium shelf bracket where the alloy is quite hard and appears to be tempered. I have put two slots in it on the rounded end, which gives me two bites of the cherry. One slot does the valve lash, the other fits the tang on the end of the clutch adjustment on the gearbox. Cheap is good, free is better.Old age creeping in.
Ahh, yes, I can see where it should be relatively easy to slot a piece of steel or aluminum to do something like that. But I think a handheld/knurled tool that you held from directly above the adjuster screw would be more versatile and less likely to foul the tank or locknut wrench.
The "use+maintenance" manual for my '17 V7III lists a "transmission oil filter" to be Checked at .9 & 6ox1000 km. Never heard of such, is there one? ronkom
Oh, and I recommend setting the valves at 4 & 6 thou again if you are planning on a remap.
I haven't got a proper stand yet for my new-ish bike to make top dead center a snap for adjustment and wasn't planning to go at them again until 6,000 miles. Thoughts?
Love the laminated carbon steel. It's a struggle to get a carbon steel knife anymore, let alone one with a laminated blade. The kids now want stainless, because they can't bother with caring for it, and don't know what a working knife looks like.I'm thinking of buying another, since they might stop making them anytime. Of course, they've only been making them for hundreds of yrs, right?https://morakniv.se/en/product-category/all-knives/morakniv-classics/?v=7516fd43adaa