Wildguzzi.com
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Donation Status
News:
Visit the Wildguzzi Amazon Affiliate Store
Home
Help
Donations
Advertise
Login
Register
Wildguzzi.com
»
General Category
»
Bike Builds, Rebuilds And Restorations Only
(Moderators:
rocker59
,
Ncdan
) »
Hydros again
« previous
next »
Print
Pages: [
1
]
Go Down
Author
Topic: Hydros again (Read 4500 times)
wirespokes
Gaggle Hero
Posts: 2452
Hydros again
«
on:
October 16, 2026, 12:00:01 PM »
I just got this 2003 Stone for $500. It's got Mistral exhaust, Ikons, dual discs, Cartridge emulators and an LED headlight. And... a ticking left side top end.
I'm not worried since the parts are worth so much more than I paid. No idea of mileage since the speedo has been replaced with a nice aftermarket. It looks well kept and low mileage. No history because the previous owner bought it at auction, not running. Soon as he started it up, discovered the noise, did some research and put it up for sale. He got one offer of $500 but didn't accept it because the guy intended to part it out. He wanted to see it repaired. I told him I intended to fix it, so he sold it to me.
I pulled the valve covers and it's got the original, from the factory, smooth lifter adjusters. Should have taken a photo, but think the spring retainers are dark. I'll drain the oil and see what comes out. If all clean, pull the pan, and if nothing, pull the front cover for a look at the pump.
At first I was thinking that a lifter just hadn't pumped up yet from sitting a long time, but now I'm betting this is the reason it went to auction.
Since the hydro kits are crazy expensive, what are my options? If the cam looks good - can I replace the lifters and pushrods and be done with it? I have another engine and could do a swap. I haven't looked at the clutch yet, but if the engine recall hasn't been done, I wouldn't expect the clutch to have been touched either. Haven't checked out the triples either.
It's a pretty nice bike with no rust, and I've got enough parts to make it right. So I won't be parting it out. I'm just trying to figure out which direction to go with it. Since I prefer carbs over FI, I might make that part of the project. If anyone knows the ins and outs of that conversion I'd like to hear what's needed. Will PHMs mount right up?
From what I've read, the hydro is a great engine, with the normal solid lifter valve springs being the root cause of all the trouble. If everything looks good with little to no wear, can the valve springs be replaced with lighter ones and all will be good?
Logged
SemperVee
My life will be told in MC people and experiences more than anything else.
Gaggle Hero
Posts: 1238
USMC Retired
Location: Seattle - ish
Re: Hydros again
«
Reply #1 on:
October 16, 2026, 03:50:18 PM »
Was just talking about this bike why no one had jumped on it when it was $900 on my FB page down in Portland OR thinking owner perhaps did not know how to adjust valves? At that price was a good parts bike since I already have an EV.
MY 03 Hydro is such a great running smooth and high torque well balanced bike. I have nothing bad to say. Great project bike. Good luck
Logged
56 years of Street Riding - All Brands
2007 MG Norge - VroomHilda
2003 Cali Hydro EV
2012 Victory CCT
2007 MG RED Norge
14 Harleys 2 VStrom 1000's
2005 BMW K1200LT, 81 R100RT, 73R/75/5
USMC Retired - Rider since 1973 - La Dolce Vita
Moto Guzzi - Making mechanics out of Riders since 1921
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #2 on:
October 16, 2026, 04:23:32 PM »
I wondered the same thing. For one, he listed it as a V7Stone -- so it would take someone in the know to realize it wasn't a V7. Also, I've got enough projects and limited space so let it ride. And then he dropped the price, and still no one took it. I guess the market is really depressed. Then again, it's the end of the riding season and no one's thinking about bikes, much less a project.
Why do you say it just needs adjusting? It does sound like loose tappets. When the hydros go bad, do they make noise? (like loose tappets?) And how would I adjust the things without a way to grab them?
The aftermarket speedo has almost 25K on it, and there's a bit more wear on things than I'd first noticed. But still, it looks pretty good over all. Of course it needs fender and a tail light, but I knew that going in. Just noticed there are no mirrors. Ah well, minor details.
Logged
SemperVee
My life will be told in MC people and experiences more than anything else.
Gaggle Hero
Posts: 1238
USMC Retired
Location: Seattle - ish
Re: Hydros again
«
Reply #3 on:
October 17, 2026, 11:54:26 AM »
RU sure it is a hydraulic Model? Not all were. Seems going backward should not be that hard. Not all got the fix.
before and after pic
Logged
56 years of Street Riding - All Brands
2007 MG Norge - VroomHilda
2003 Cali Hydro EV
2012 Victory CCT
2007 MG RED Norge
14 Harleys 2 VStrom 1000's
2005 BMW K1200LT, 81 R100RT, 73R/75/5
USMC Retired - Rider since 1973 - La Dolce Vita
Moto Guzzi - Making mechanics out of Riders since 1921
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #4 on:
October 18, 2026, 07:33:05 AM »
Yes, it definitely has the original adjusters like your top photo.
I got the wild idea to call the local dealer here in Portland Oregon to see about getting the kit. I was asked for the VIN and it turns out this bike isn't listed as having had the recall. It's eligible. WOW! So they're on order and the wait begins. I thought there were no more kits available. Any idea how long it might take for this stuff to arrive?
I always do my own work, so am hesitant putting it in someone else's hands. What's the consensus on the Portland dealer? Can I trust them?
In the meantime, I'll do my own research into the condition of the engine. Pull the oil pump, and if it's worn with indications of having seen a lot of metal in the oil, I'll pull a cylinder for a look at the piston. That way I'll ensure the complete job is done. Take it in half disassembled.
I'm guessing that with lifter noise happening, a bunch of wear has already occurred and it could be a real mess in there. What do you think?
It also has the single plate clutch - I wondered about how easy the clutch pulled in. Now I know. Is there a replacement single plate clutch disc now that doesn't fail early? Why do these fail when the BMWs don't? Also, it appears the clutch isn't a recall item. I read that the clutch hub is different - shorter?
The lower triple tree looks fine, so my guess is that it won't be an issue.
Logged
SemperVee
My life will be told in MC people and experiences more than anything else.
Gaggle Hero
Posts: 1238
USMC Retired
Location: Seattle - ish
Re: Hydros again
«
Reply #5 on:
October 18, 2026, 09:35:32 AM »
Haven't heard anything bad or good about the Portland dealer. Good that you can access the cam kit. Running well you will be amazed how much torque the 1100 has with the 5 speed. My Norge just passed 50K miles is good with 25 more HP but seems less torque then the 1100 - from the seat of the pants feeling... and S M O O T H. Both are. My Clutch was replaced with double plate when purchased and took about 6 hrs dealer labor. Not easy job but if yours feels fine I would leave it alone. There is a lot to like about the 1100 series. If you want come a few hours north to see a perfect running example..Then again you might want to take mine home.. :^)
«
Last Edit: October 18, 2026, 12:19:22 PM by SemperVee
»
Logged
56 years of Street Riding - All Brands
2007 MG Norge - VroomHilda
2003 Cali Hydro EV
2012 Victory CCT
2007 MG RED Norge
14 Harleys 2 VStrom 1000's
2005 BMW K1200LT, 81 R100RT, 73R/75/5
USMC Retired - Rider since 1973 - La Dolce Vita
Moto Guzzi - Making mechanics out of Riders since 1921
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #6 on:
October 19, 2026, 12:33:05 PM »
Gorgeous bike! You're right - I'd want to take it home.
I've done a clutch, or something related, on just about every Guzzi I've owned so far, so why should this one be any different? LOL
I'm collecting parts for when that day comes.
I keep hearing how great these hydros are, but have a hard time believing it. All of my Guzzis are smooth and strong, even the 850. It has me wondering.
Logged
SemperVee
My life will be told in MC people and experiences more than anything else.
Gaggle Hero
Posts: 1238
USMC Retired
Location: Seattle - ish
Re: Hydros again
«
Reply #7 on:
October 19, 2026, 01:31:25 PM »
I have to let go of one of my Guzzi's, the Hydro or the Norge but I have to say I am with 50+K miles on VroomHilda partial to the Norge, but I love them both. I look at the 03 as a collector classic a bit.
«
Last Edit: October 20, 2026, 08:38:54 AM by SemperVee
»
Logged
56 years of Street Riding - All Brands
2007 MG Norge - VroomHilda
2003 Cali Hydro EV
2012 Victory CCT
2007 MG RED Norge
14 Harleys 2 VStrom 1000's
2005 BMW K1200LT, 81 R100RT, 73R/75/5
USMC Retired - Rider since 1973 - La Dolce Vita
Moto Guzzi - Making mechanics out of Riders since 1921
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #8 on:
October 19, 2026, 10:58:13 PM »
That's funny thinking of the 03 as a collector classic. It seems like a new bike to me.
Logged
Road Scholar
New Egg
Posts: 4
Location: Texas
Re: Hydros again
«
Reply #9 on:
November 04, 2026, 03:09:18 PM »
At approximately what mileage would a 2003 California Stone start to exhibit potential camshaft wear?
Symptoms, other than unusual valve chatter?
Logged
Roman Hordan
Hatchling
Posts: 27
Location: United Kingdom
Re: Hydros again
«
Reply #10 on:
November 05, 2026, 03:33:17 AM »
There's no real mileage number for it. Some of these cams went bad in the low thousands, and plenty of bikes have run 50K+ with no trouble, so it seems to depend more on the individual bike and how it was cared for. Oil changes and warm-up habits probably matter too.
Besides the chatter, I'd look for:
- Fine metallic glitter in the oil, on the drain plug, or in the cut-open oil filter. This is the biggest red flag.
- A tick that gets worse as the engine warms up, or that sticks around instead of fading after a minute or two.
- A cylinder that runs rough or has lost some power.
- Low oil pressure at hot idle.
If you can get the valve covers off, you can also see how the lifter faces look. Check the VIN with a dealer to see whether the recall was done on yours, since that's what wirespokes found on his.
Logged
BMCMOTO
Gaggle Hero
Posts: 954
Location: East Lansing, MI
Re: Hydros again
«
Reply #11 on:
November 05, 2026, 07:52:27 AM »
Checking the VIN with a dealer is not necessarily going to yield correct information. The dealership I worked at got many that had been reported as done that were not. Conflict between dealers and the mother ship was the cause. Pulling a valve cover is the only real way to check and even that can be imperfect. Pull a valve cover and post a picture and someone will chime in. If the valve retainer is aluminum, it has probably been done.
Brian
Logged
1989 MILLE GT
2006 BREVA 750
2004 BREVA 750
1975 CONVERT
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #12 on:
November 09, 2026, 03:25:58 PM »
My next step is draining the oil to see how bad it is. Hopefully not too glittery. I'm thinking I should pull the front cover and open up the oil pump. What I'm afraid of, is the shop just routinely replacing the cam and lifters without checking deeper. So if I determine the oil pump is fried, that would force the issue to go the extra mile - cleaning oil passages, rod and main bearings, checking bores, etc. However, not knowing the policy on all this, I don't know if my going in there would violate the recall.
Logged
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #13 on:
November 11, 2026, 07:06:40 PM »
Got a call from Dominick at the shop yesterday that the parts were in. So today I took it in to them. I was told the new triple tree would get done tomorrow and I could pick it up.
As it turns out, Dominick knew nothing about hydros. He had looked up the vin and saw there was a recall on the triple tree and told me to bring it in. He showed me the screen and there was no mention of a hydro recall for this bike.
Frankly, I was pretty surprised Guzzi would still honor a 23-year-old recall - but now I wonder why it didn't show up on the warranty/recall screen? Dominick said that if I could get him the Campaign Code he could check it out. Any of you have something showing the Campaign Code?
So I'm now back to square one, needing to tear into the bike to see what I've got. And also, I probably wouldn't have gone to the trouble of hauling the bike in had I known it was just for the triple tree. The invoice (no charge to me) showed the triple ($1000), a bearing (I don't recall the price, but it wasn't cheap) and labor of something like $900.
Logged
BMCMOTO
Gaggle Hero
Posts: 954
Location: East Lansing, MI
Re: Hydros again
«
Reply #14 on:
November 12, 2026, 05:20:59 AM »
Just pull a valve cover and post a Pic.
Brian
Logged
1989 MILLE GT
2006 BREVA 750
2004 BREVA 750
1975 CONVERT
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #15 on:
November 12, 2026, 11:26:00 AM »
I can take a pic, but it very definitely is a hydro and hasn't been done. My question now is this - not knowing how the Piagio data base works, what comes up on a VIN search? I'd think that if there was a recall, it would come up as either done or not. And if it's beyond a time limit (20 years?) it would note that as well.
In this case, a search of the VIN only brings up the steering stem recall, which is still valid 23 years later. Does that mean this bike wasn't part of the recall?
I'm having difficulty getting to the bottom of this with the dealer. For one thing, it was before his time, he's not really interested, and finally, there's no money in it for him that he can tell. His interest seems to be in racing new Aprilias.
I'm now beginning to wonder if this engine isn't original to the bike
Logged
Road Scholar
New Egg
Posts: 4
Location: Texas
Re: Hydros again
«
Reply #16 on:
November 15, 2026, 08:01:12 AM »
A 2004 California Stone (hydro motor) is for sale nearby. Seller has had it for three years and has put 5,000 miles on it. No reported issues. He has not pulled the valve covers.
He has changed the oil twice. No metal in the filter or on the magnetic plug. Seller is reputable and owns several Guzzi's.
I test rode the bike. No unusual sounds from valves or drive train. Bike started up fine both cold and hot. No smoke. Ran good, shifted and stopped as it should. No leaks, good tires. Newer battery. Cosmetically not perfect. Some pitting on chrome, paint ok, small crack in lower part of windshield. All lights work.
Total mileage is unknown. Odometer died at some stage and the replacement done in 2023 now shows 5K.
When I put the VIN in the Piaggio website, it says the bike "is not involved in a recall campaign".
I plan on calling the local dealer to see if they can bring anything up but not sure if they will be able to tell me much...
Best case: bike was fixed at the factory or the dealer before sale. Or, bike was fixed by previous owner and Piaggio website is accurate (insert laughter here)
Worst case: bike is a time bomb. I will be out a couple of grand and have a new boat anchor. And I don't even own a boat
There seems to be some evidence that the bike may be OK and a serious issue should have surfaced by now (like the single plate clutch). I have read some comments that by 2004, the factory had resolved the problem with the hydraulic valves. I did not look at the triple tree but I will before I proceed.
I realize the only way to know for sure is to pull the valve cover to see if the recall was done.
This would be my first Guzzi and I'd hate to start off with a lemon.
Logged
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #17 on:
November 15, 2026, 05:46:20 PM »
Road Scholar - I don't know what to tell you. I've heard that the speedometers fail so it's difficult knowing just how many miles they've gone. And the mileage is good data to have when evaluating a 'new' bike.
When I just punched mine into the recall data base, nothing came up. Evidently it won't tell you if it's been done, just that it's not listed as needing to be done. So perhaps yours was done. If you could remove a valve cover and snap a photo, we could tell you yes or no.
The dealer told me that my VIN was earlier than the recall dates. He said I should consider myself lucky. Huh? Why is that a good thing when I have a hydro and it's failing? He said it has 24K miles after all. It's an old bike and stuff fails.
Where do you find people like this??? I'm also not particularly pleased with the work done and am really glad they didn't touch the engine.
I'm trying to decide where to go from here. I'm strongly considering replacing the cam if needed, installing solid lifters with the correct pushrods, and tappet adjusters. Just make it a non hydro. That's if there's no other damage.
When I removed the left side valve cover, the exhaust tappet had a good 1/8" of slop. No wonder it was making noise! I didn't even try to see what the intake is since I know it'll have to come apart. Maybe I should check it since if it's ok - that might indicate the problem is only with the exhaust lifter.
Anyway - is it possible to swap over the solid lifters and associated parts without any major changes to the engine. Are the cams the same?
Logged
BMCMOTO
Gaggle Hero
Posts: 954
Location: East Lansing, MI
Re: Hydros again
«
Reply #18 on:
November 15, 2026, 09:06:13 PM »
Swapping to solid cam followers is not practical, different diameters. The worst ones we saw got new engines. Metal particals embedded in the teflon coated piston skirts, cylinders worn through the nigasil coating, oil pumps trashed. The fix really is based on lighter valve springs. There were actually four different attempts to fix the problem the first three obviously failed.
Brian
Logged
1989 MILLE GT
2006 BREVA 750
2004 BREVA 750
1975 CONVERT
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #19 on:
November 15, 2026, 10:08:35 PM »
Thanks BMC. Yes, I just discovered that the hydraulic lifters are a smaller diameter. Boring out the lifter bores isn't practical.
I've just checked and it's only the left side exhaust lifter that's malfunctioning. Maybe I'll get lucky and it's only a collapsed lifter. I can always hope. The fact it's not coming up on the recall database could be that it was done - and hopefully with the fourth and final fix.
And if it is a bad lifter only, once fixed I should probably pull the valve springs and check or replace them to the lighter weight spec.
My question now is whether I can pull the lifter without pulling the head and cylinder. I could pull the rockers and if it won't come out, keep going. Guess I answered my own question.
Logged
BMCMOTO
Gaggle Hero
Posts: 954
Location: East Lansing, MI
Re: Hydros again
«
Reply #20 on:
November 16, 2026, 07:00:53 AM »
The cam follower is footed, the "hydraulic lifter" sits in the cam follower. I think the lifter is too large in diameter to come out of the follower and up the pushrod tunnel. The footed cam follower will only come out the bottom after removing the camshaft. Pulling the pan will give a view up into the crankcase and the cam surface. The piston skirts may also be in view at this stage. If the valve spring retainers are aluminum the springs have probably been done. The springs that replaced the the originals came from an earlier model, maybe a loop frame engine, just can't remember. My experience with this stuff is pretty aged, it's over 20 years ago now.
Brian
Logged
1989 MILLE GT
2006 BREVA 750
2004 BREVA 750
1975 CONVERT
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #21 on:
November 16, 2026, 02:59:13 PM »
I'll take a photo of the head, but it appears to me nothing was done to this engine. The adjusters aren't snapped off (smooth, factory-like) and it doesn't have aluminum retainers.
Here's my question: if the cam is ok, I don't find a bunch of glitter in the oil, and it's only a collapsed lifter, would it be reasonable to replace the one bad lifter and install the lighter valve springs and call it good?
Yes, I've read that the lifter can't come out the top, unfortunately. Evidently the cam must be removed to replace it.
I rotated the engine through a few cycles and the pushrod moves, what appears to be, a full stroke. But I should measure exact lift to know for sure. It's possible I may be lucky and have only a lifter failure.
Logged
BMCMOTO
Gaggle Hero
Posts: 954
Location: East Lansing, MI
Re: Hydros again
«
Reply #22 on:
November 16, 2026, 06:50:50 PM »
If you did that you might save it. Were it mine, I'd pull the pan and take a look. I have often wondered if one could be saved by this method. I'm not sure I recall correctly but I think all of the factory fixes before the final one with the valve springs consisted of cams and followers as well as adjustable rocker arms and measuring tools including a dummy hydraulic lifter for setting up valve lash. Installed spring height was/is critical. Somewhere there was a file with all the recall info including part numbers and instructions. It might have been "This Old Tractor" Greg Bender's most helpful web site.
Brian
Logged
1989 MILLE GT
2006 BREVA 750
2004 BREVA 750
1975 CONVERT
Road Scholar
New Egg
Posts: 4
Location: Texas
Re: Hydros again
«
Reply #23 on:
November 17, 2026, 07:55:11 AM »
I think this is the doc BCMOTO refers to:
https://www.thisoldtractor.com/mg_manuals/instructions_hydraulic_tappet_refitting_camshaft_recall.pdf
Logged
wirespokes
Gaggle Hero
Posts: 2452
Re: Hydros again
«
Reply #24 on:
November 17, 2026, 09:31:20 PM »
Thanks for directing me to Bender's site. That document helps a lot.
Pulled the pan and found a very slight bit of very small flakes. Haven't strained the oil yet.
The magnet is missing, but I might have a small one that could fit. You know, it's
really difficult to see the cam lobes past the crank. What I could see of the bores looked fine. No scoring, just normal crosshatch. I'm in the process of removing the
alternator rotor and that 24mm nut doesn't want to come loose. First gear with rear brak on isn't doing it. I probably should have pulled it before removing the front engine bolt, and jammed a 2x4 between the crank and case. Can't do that now unless I replace the front bolt. The pan is held on with 2 bolts so not a big deal.
Logged
*IMPROVED* - Wildguzzi Amazon Affiliate Storefront!
Proceeds go back into the forum.
If you need to buy it anyway, use the affiliate link to help the forum.
Advertise Here
Print
Pages: [
1
]
Go Up
« previous
next »
Wildguzzi.com
»
General Category
»
Bike Builds, Rebuilds And Restorations Only
(Moderators:
rocker59
,
Ncdan
) »
Hydros again
Shop our affiliate storefront
Proceeds go back into the forum.
If you need to buy it anyway, use the affiliate link to help the forum.
Advertise Here