Author Topic: DIY Fuel Cap Key Eliminator  (Read 1781 times)

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
DIY Fuel Cap Key Eliminator
« on: October 23, 2026, 09:41:46 AM »
I have to say that I do not see how there is an issue with the plastic expanding causing the lock to become hard to turn. What I noticed was a lot of corrosion on the aluminum lock barrel and steel pieces. I didn't really like the looks of Harper's eliminator, plus it costs about $100 delivered. And it's aluminum so it's not going to resolve the corrosion issue. So I sourced a stainless 38mm knurled knob and a length of 1/2" stainless rod.





And after a bit of time on my mini-mill, I have my key eliminator.



« Last Edit: November 04, 2026, 01:34:04 PM by sk66 »
Steven
2014 California 1400 Touring

Online Dirk_S

  • www.dirkshearer.com
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 2502
  • Doodler of doodles
    • www.DirkShearer.com
  • Location: Portland, Maine, U.S.
Re: DIY Fuel Cap Key Eliminator
« Reply #1 on: October 23, 2026, 09:45:44 AM »
Looks lovely. Looks like it can also allow moisture in. Would a big o-ring or gasket be wise for that setup?

Also—I want a mini mill. Right up my DIY alley and apartment-dwelling real estate allowance.

Current: '18 Guzzi V7 III Rough, '17 Guzzi V9 Bobber, ‘78 BMW R80/7, 1986 Sputnik sidecar

Previous: '16 Guzzi V7 II Stone, ‘15 Ural Gear Up, '11 Suzuki TU250X, ‘86 Guzzi V65 Lario, '78/‘80 Honda CX500, '77 Kawasaki KZ400 Special

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #2 on: October 23, 2026, 10:17:43 AM »
Looks lovely. Looks like it can also allow moisture in. Would a big o-ring or gasket be wise for that setup?

Also—I want a mini mill. Right up my DIY alley and apartment-dwelling real estate allowance.

Thanks.
The OEM lock barrel also lets water in; that's probably the main cause of the corrosion issue. But there is an o-ring at the bottom that prevents the water from getting into the tank. I did try adding an o-ring to the top as well,but it causes the knob to stand more proud the thickness of the ring and I don't have a thin one on hand. I guess I could add a recessed groove for one...

Edit: 1.5mm FKM o-ring ordered...
« Last Edit: October 23, 2026, 11:14:15 AM by sk66 »
Steven
2014 California 1400 Touring

Offline DoubleGuzzi

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • Posts: 975
  • '19 V7III CarbonS; '11 750Breva; '79 V50II.
  • Location: NE Écosse
Re: DIY Fuel Cap Key Eliminator
« Reply #3 on: October 24, 2026, 01:07:04 PM »
No locking fuel cap; you guys don't leave bikes parked overnight in shady places? Siphoned fuel or sugar in the tank (just for kicks).  :undecided:
Nearly natural progression..
Past: SS50, Z200, Z250B, Z400J, (H100), GT750, K100, ZR1100, 900 Trident, 955 Sprint ST, (ZR550, M600), 900 ST, (B750), (V7C).
Present: V7III CS, (V50II), (Breva 750)

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: DIY Fuel Cap Key Eliminator
« Reply #4 on: October 24, 2026, 01:40:49 PM »
Looks lovely. Looks like it can also allow moisture in. Would a big o-ring or gasket be wise for that setup?

Also—I want a mini mill. Right up my DIY alley and apartment-dwelling real estate allowance.



Taig tools, I have one long before they were $1K. Meanwhile used Bridgeports are selling for less than $1K and that machine will do magic in the right hands. Of course they are not portable.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Online Dirk_S

  • www.dirkshearer.com
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 2502
  • Doodler of doodles
    • www.DirkShearer.com
  • Location: Portland, Maine, U.S.
Re: DIY Fuel Cap Key Eliminator
« Reply #5 on: October 24, 2026, 05:05:30 PM »
No locking fuel cap; you guys don't leave bikes parked overnight in shady places? Siphoned fuel or sugar in the tank (just for kicks).  :undecided:

Shady places?? Harrisburg, it may not be the safest city in Pennsylvania, but it at least isn’t London  :evil: By that I just mean, most U.S. cities don’t experience as high of motorbike theft/vandalism, etc. that we know happens across the pond.
« Last Edit: October 24, 2026, 10:39:16 PM by Dirk_S »
Current: '18 Guzzi V7 III Rough, '17 Guzzi V9 Bobber, ‘78 BMW R80/7, 1986 Sputnik sidecar

Previous: '16 Guzzi V7 II Stone, ‘15 Ural Gear Up, '11 Suzuki TU250X, ‘86 Guzzi V65 Lario, '78/‘80 Honda CX500, '77 Kawasaki KZ400 Special

Online AJ Huff

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 4272
  • Location: College Community IA
Re: DIY Fuel Cap Key Eliminator
« Reply #6 on: October 24, 2026, 10:27:07 PM »
Seriously? Maybe mid-20th century but I'd call that an urban legend now. I doubt anyone under the age of 50 even knows how to siphon gas. And to get maybe a gallon or two? I've never even thought to worry about this. And sugar in the tank? That sounds like an angry ex-wife thing at best.

-AJ

No locking fuel cap; you guys don't leave bikes parked overnight in shady places? Siphoned fuel or sugar in the tank (just for kicks).  :undecided:
'71 Ambassador
'01 California Special
'05 Road King
MGNOC# L-753

Online Dr. Enzo Toma

  • Gaggle Hero
  • *****
  • *
  • *
  • Posts: 745
  • Location: Colorado, US
Re: DIY Fuel Cap Key Eliminator
« Reply #7 on: October 24, 2026, 11:49:59 PM »
I think your comment about people under the age of 50 is quite an exaggeration ;) , but I have to agree with the rest. Aside from people sabotaging vehicles for political reasons, I've never heard of anyone actually messing with a vehicle's fuel system like that. Closest would be people stealing spare fuel containers off of bikes.
2027 Moto Guzzi V7 Sport
MGNOC Member

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #8 on: October 25, 2026, 07:46:44 AM »
No locking fuel cap; you guys don't leave bikes parked overnight in shady places? Siphoned fuel or sugar in the tank (just for kicks).  :undecided:
No. And sugar doesn't dissolve in gas... that's mostly a myth.
Plus, I'm not the type to worry too much about what could possibly happen... If I were I probably wouldn't ride a bike.
« Last Edit: October 25, 2026, 08:09:42 AM by sk66 »
Steven
2014 California 1400 Touring

Online michaell32

  • Gosling
  • ***
  • *
  • *
  • *
  • *
  • Posts: 187
  • Location: Salt Lake City
Re: DIY Fuel Cap Key Eliminator
« Reply #9 on: October 25, 2026, 08:17:34 AM »
No locking fuel cap; you guys don't leave bikes parked overnight in shady places? Siphoned fuel or sugar in the tank (just for kicks).  :undecided:
If someone empties my tank on one of my motorcycles I lose a maximum of 20 bucks. If a key breaks one time I lose a lot more money. I remove locking gas caps on everything I own.
2003 California EV
2018 Suzuki DR650
78 Honda GL1000

Offline nc43bsa

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 1506
  • Location: Mooresville NC
Re: DIY Fuel Cap Key Eliminator
« Reply #10 on: October 25, 2026, 12:19:14 PM »
If someone empties my tank on one of my motorcycles I lose a maximum of 20 bucks. If a key breaks one time I lose a lot more money. I remove locking gas caps on everything I own.

Good point.
1990 MilleGT

Offline DoubleGuzzi

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • Posts: 975
  • '19 V7III CarbonS; '11 750Breva; '79 V50II.
  • Location: NE Écosse
Re: DIY Fuel Cap Key Eliminator
« Reply #11 on: October 25, 2026, 08:20:45 PM »
Sheltered lives.  :lipsrsealed:

(Have you had a 'bike nicked, or your (same) house robbed three times? Rhetorical.)

 :bike-037:
Nearly natural progression..
Past: SS50, Z200, Z250B, Z400J, (H100), GT750, K100, ZR1100, 900 Trident, 955 Sprint ST, (ZR550, M600), 900 ST, (B750), (V7C).
Present: V7III CS, (V50II), (Breva 750)

Online Dr. Enzo Toma

  • Gaggle Hero
  • *****
  • *
  • *
  • Posts: 745
  • Location: Colorado, US
Re: DIY Fuel Cap Key Eliminator
« Reply #12 on: October 25, 2026, 09:09:49 PM »
If someone empties my tank on one of my motorcycles I lose a maximum of 20 bucks. If a key breaks one time I lose a lot more money. I remove locking gas caps on everything I own.

I had a 1974 IH Scout II pickup truck and the lock on the gas cap froze in the winter. I went into the gas station to see if they had any kind of deicer products, walked out with a gallon of anti-freeze and a can of WD-40 hoping one of them would work, my buddy who was waiting in the truck had already thawed the locking GAS cap... with a lighter 🤦 I promptly ordered a non-locking gas cap after that.





Not an issue for my motorcycles as none of the ones that get ridden in below freezing weather have an exposed locking gas cap.
This is a nicely executed key eliminator, but my issue with a cap on my Guzzi is that it isn't hinged so I need somewhere, preferably clean, to set the fuel cap while filling the tank.

2027 Moto Guzzi V7 Sport
MGNOC Member

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #13 on: October 26, 2026, 08:40:21 AM »
This is a nicely executed key eliminator, but my issue with a cap on my Guzzi is that it isn't hinged so I need somewhere, preferably clean, to set the fuel cap while filling the tank.

I guess that's one potential negative about the lock eliminator... it's now possible to drive off leaving the cap behind; but I highly doubt I would make it far at all.
Steven
2014 California 1400 Touring

Online Dirk_S

  • www.dirkshearer.com
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 2502
  • Doodler of doodles
    • www.DirkShearer.com
  • Location: Portland, Maine, U.S.
Re: DIY Fuel Cap Key Eliminator
« Reply #14 on: October 26, 2026, 08:45:39 AM »
This is a nicely executed key eliminator, but my issue with a cap on my Guzzi is that it isn't hinged so I need somewhere, preferably clean, to set the fuel cap while filling the tank.

The day that my adult ADHD leads me to forget to put my gas cap back on my tank just ONCE, I’ll begin to consider clutchless shifting, gyroscopic balancing, and electric power. Gas cap has always either been placed on top of the fuel pump box or my seat.
Current: '18 Guzzi V7 III Rough, '17 Guzzi V9 Bobber, ‘78 BMW R80/7, 1986 Sputnik sidecar

Previous: '16 Guzzi V7 II Stone, ‘15 Ural Gear Up, '11 Suzuki TU250X, ‘86 Guzzi V65 Lario, '78/‘80 Honda CX500, '77 Kawasaki KZ400 Special

Offline DoubleGuzzi

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • Posts: 975
  • '19 V7III CarbonS; '11 750Breva; '79 V50II.
  • Location: NE Écosse
Re: DIY Fuel Cap Key Eliminator
« Reply #15 on: October 27, 2026, 02:45:57 PM »
.. forget to put my gas cap back on my tank just ONCE..
Hence the interest in using a Triumph Monza-type cap.  :wink:
Nearly natural progression..
Past: SS50, Z200, Z250B, Z400J, (H100), GT750, K100, ZR1100, 900 Trident, 955 Sprint ST, (ZR550, M600), 900 ST, (B750), (V7C).
Present: V7III CS, (V50II), (Breva 750)

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #16 on: October 29, 2026, 03:07:56 PM »
Updated with o-ring.





I have enough rod and o-rings to make quite a few more if anyone is interested.
Steven
2014 California 1400 Touring

Offline Motormike

  • Gaggle Hero
  • *****
  • Posts: 1762
  • Location: Tennessee
Re: DIY Fuel Cap Key Eliminator
« Reply #17 on: October 30, 2026, 12:09:05 PM »
Seriously? Maybe mid-20th century but I'd call that an urban legend now. I doubt anyone under the age of 50 even knows how to siphon gas. And to get maybe a gallon or two? I've never even thought to worry about this.
-AJ

It would be easier to steal the bike than steal the gas!!  :rolleyes:

Online elrealistico

  • Gosling
  • ***
  • *
  • *
  • *
  • *
  • Posts: 235
  • Location: Central Florida USA
Re: DIY Fuel Cap Key Eliminator
« Reply #18 on: October 30, 2026, 01:39:23 PM »
No, if my hous'ed been broke into 3x, I'd be installing very heavy shutters and doors and dogs or maybe move?

But it's a nice little peice of work. I'd buy one, but a little too late. Already got the Harper's one with my last order of stuff from Curtis. I don't have the machines or the skills to do myself. I am at the point in life I really don't want to buy more expensive space-occupying dust gathering things. I have a wife to do that for me!


Sheltered lives.  :lipsrsealed:

(Have you had a 'bike nicked, or your (same) house robbed three times? Rhetorical.)

 :bike-037:
2018 V7III Special
1978 T140V Bonneville
2004 EV Touring

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #19 on: October 30, 2026, 06:23:51 PM »
Updated again.
On the original key barrel there is a protrusion which limits the key turn to 90˚. None of the other replacements (Harper, GT) have that protrusion so I thought I didn't need it. Well, I found I could turn the knob 180˚ and over-tighten the cap, which makes it very difficult to remove.





Just don't use as much force and stop at 90˚; easy enough right? Nope... I added the protrusion...  :cheesy:



« Last Edit: November 02, 2026, 04:11:22 PM by sk66 »
Steven
2014 California 1400 Touring

Online TN Mark

  • Gaggle Hero
  • *****
  • *
  • *
  • Posts: 1335
Re: DIY Fuel Cap Key Eliminator
« Reply #20 on: October 30, 2026, 09:13:42 PM »
Yours is very close to the one GTM made.
I have the GTM one on my desk and will post a
picture of it here tomorrow.

I may have purchased the last one GTM had available. It looks like this:






It’s never been installed and I’m not certain I will install it. I have no issue with the keyed gas cap on my 2016 Eldorado.

Thank you very much for doing things like this. Our community can certainly use the support.
« Last Edit: November 01, 2026, 09:08:38 PM by TN Mark »

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #21 on: November 01, 2026, 09:38:30 AM »
Yours is very close to the one GTM made.
I have the GTM one on my desk and will post a
picture of it here tomorrow.
Yes. My problem with it is twofold... it wasn't available (out of stock) and it looks like this after a few years of use.





I'm actually on my 5th version now; going for #6 soon.
1. machined from raw aluminum- corrosion
2. stainless- didn't like the knob/aesthetics
3. this knob
4. added o ring- for improved water protection
5. added stop pin- to prevent over tightening
6. plan for integral pin- why; I don't know... because I can I guess.
« Last Edit: November 01, 2026, 10:10:24 AM by sk66 »
Steven
2014 California 1400 Touring

Online SemperVee

  • My life will be told in MC people and experiences more than anything else.
  • Gaggle Hero
  • *****
  • *
  • *
  • Posts: 1242
  • USMC Retired
  • Location: Seattle - ish
Re: DIY Fuel Cap Key Eliminator
« Reply #22 on: November 01, 2026, 09:47:24 AM »
Updated with o-ring.





I have enough rod and o-rings to make quite a few more if anyone is interested.

Nice of you to offer your talented handicraft for this.  What might the cost be for those interested?  What year bikes would it fit? All lift off caps like  the earlier Cali's? 
« Last Edit: November 01, 2026, 09:57:32 AM by SemperVee »
56 years of Street Riding - All Brands
2007 MG Norge - VroomHilda
2003 Cali Hydro EV
2012 Victory CCT
2007 MG RED Norge
14 Harleys 2 VStrom 1000's
2005 BMW K1200LT, 81 R100RT, 73R/75/5

USMC Retired - Rider since 1973 - La Dolce Vita
Moto Guzzi - Making mechanics out of Riders since 1921

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #23 on: November 01, 2026, 10:08:40 AM »
Nice of you to offer your talented handicraft for this.  What might the cost be for those interested?
If someone wants this last one I'll let it go cheap (assuming version 6 is a success)... PM me.
If machining a new one from existing stock, I anticipate around $65 for version 6 ($70 delivered lower 48; assuming making the pin integral is easier/quicker than adding it).
Steven
2014 California 1400 Touring

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #24 on: November 01, 2026, 10:15:38 AM »
What year bikes would it fit? All lift off caps like  the earlier Cali's?
It should fit all bikes with the earlier key lock cap (not screw in). This is Harper's compatibility list (not verified by me):

MOTO GUZZI - CALIFORNIA
 California Alum./Tit. PI Cat. 1100 2003-2004 (APAC, EMEA, NAFTA)
 California EV/EV Touring/80 1100 2001-2002 (APAC, EMEA, NAFTA)
 California EV/EV Touring PI 1100 2002 (APAC, EMEA, NAFTA)
 California EV PI Cat. 1100 2003-2005 (APAC, EMEA, NAFTA)
 California EV V11 EV USA 1100 1997-2000 (APAC, EMEA, NAFTA)
 California Jackal 1100 1999-2001 (APAC, EMEA, NAFTA)
 California Special 1100 1999-2000 (APAC, EMEA, NAFTA)
 California Special Sport/Al. PI 1100 2002, California Stone/Metal PI 1100 2002
 California Special Sport 1100 2001-2002 (APAC, EMEA, NAFTA)
 California Stone/Metal PI 1100 2002 (APAC, EMEA, NAFTA)
 California Stone/Touring PI Cat 1100 2003-2004 (APAC, EMEA, NAFTA)
 California Stone 1100 2001-2002 (APAC, EMEA, NAFTA)
 California 1400 Corazzieri E3 ABS 2016 (EMEA)
 California 1400 Custom E3 ABS 2012-2013 (APAC, EMEA, NAFTA)
 California 1400 Custom E3 ABS 2015 (NAFTA)
 California 1400 Touring E3 ABS 2012-2014 (APAC, EMEA, NAFTA)
 California 1400 Touring E3 ABS 2015 (EMEA, NAFTA)
 California 1400 Touring E4 ABS 2017-2018-2020 (NAFTA)
 California 1400 Touring E4 ABS 2017-2020 (APAC)
 California 1400 Touring E4 ABS 2017-2020 (EMEA)
 California 1400 Touring SE E3 ABS 2015-2016 (APAC, EMEA)
 California 1400 Touring SE E3 ABS 2016 (NAFTA)
MOTO GUZZI - ELDORADO
 Eldorado 1400 E3 ABS 2015-2016 (APAC, EMEA)
 Eldorado 1400 E4 ABS 2016 (NAFTA)
 Eldorado 1400 E4 ABS 2017-2018-2019-2020 (NAFTA)
 Eldorado 1400 E4 ABS 2017-2020 (APAC)
 Eldorado 1400 E4 ABS 2017-2020 (EMEA)
MOTO GUZZI - V 7
 V7 Cafè 750 E3 2009 (APAC, EMEA, NAFTA)
 V7 Classic 750 E3 2008-2012 (APAC, EMEA, NAFTA)
 V7 II Racer 750 E3 ABS 2015-2016 (APAC, EMEA)
 V7 II Racer 750 E3 ABS 2016 (NAFTA)
 V7 II Special 750 E3 ABS 2015-2016 (APAC, EMEA)
 V7 II Special 750 E3 ABS 2016 (NAFTA)
 V7 II Stone 750 E3 ABS 2015-2016 (APAC, EMEA)
 V7 II Stone 750 E3 ABS 2016 (NAFTA)
 V7 II Stornello 750 E3 ABS 2016 (APAC)
 V7 II Stornello 750 E3 ABS 2016 (NAFTA)
 V7 Racer 750 E3 2011-2012 USA (EMEA, NAFTA)
 V7 Racer 750 E3 2012-2013 2013-2014 USA (EMEA, NAFTA)
 V7 Racer 750 E3 2014 (APAC, EMEA)
 V7 RACER 750 E3 2015 (NAFTA)
 V7 Special 750 E3 2015 (NAFTA)
 V7 Special E3 750 2014 (APAC, EMEA)
 V7 Special-Stone E3 750 2012-2013 (APAC, EMEA, NAFTA)
 V7 Stone 750 E3 2014 (APAC, EMEA)
 V7 Stone 750 E3 2015 (NAFTA)
MOTO GUZZI - AUDACE and MGX21 (all?)
« Last Edit: November 01, 2026, 10:20:31 AM by sk66 »
Steven
2014 California 1400 Touring

Online Dirk_S

  • www.dirkshearer.com
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • *
  • Posts: 2502
  • Doodler of doodles
    • www.DirkShearer.com
  • Location: Portland, Maine, U.S.
Re: DIY Fuel Cap Key Eliminator
« Reply #25 on: November 01, 2026, 05:11:01 PM »
Yes. My problem with it is twofold... it wasn't available (out of stock) and it looks like this after a few years of use.





Whelp, if you weren’t banned from his forum before now…welcome to the club  :laugh:
Current: '18 Guzzi V7 III Rough, '17 Guzzi V9 Bobber, ‘78 BMW R80/7, 1986 Sputnik sidecar

Previous: '16 Guzzi V7 II Stone, ‘15 Ural Gear Up, '11 Suzuki TU250X, ‘86 Guzzi V65 Lario, '78/‘80 Honda CX500, '77 Kawasaki KZ400 Special

Online TN Mark

  • Gaggle Hero
  • *****
  • *
  • *
  • Posts: 1335
Re: DIY Fuel Cap Key Eliminator
« Reply #26 on: November 01, 2026, 09:17:05 PM »
Updated again.
On the original key barrel there is a protrusion which limits the key turn to 90˚. None of the other replacements (Harper, GT) have that protrusion so I thought I didn't need it. Well, I found I could turn the knob 180˚ and over-tighten the cap, which makes it very difficult to remove.

Just don't use as much force and stop at 90˚; easy enough right? Nope... I added the protrusion...  :cheesy:






Really appreciate what you’re doing with this sk66.
Thank you sir, thank you very, very much!
Our community most certainly needs all the support people like you with nice products can offer.

Online sk66

  • Hatchling
  • **
  • Posts: 23
  • Location: Harrisburg PA
Re: DIY Fuel Cap Key Eliminator
« Reply #27 on: November 04, 2026, 01:35:02 PM »
Version 6- final





This has to be the most expensive key lock eliminator ever...
« Last Edit: November 04, 2026, 01:42:08 PM by sk66 »
Steven
2014 California 1400 Touring

Online TN Mark

  • Gaggle Hero
  • *****
  • *
  • *
  • Posts: 1335
Re: DIY Fuel Cap Key Eliminator
« Reply #28 on: November 04, 2026, 02:02:10 PM »
Very impressive, thank you sir.

 

Shop our affiliate storefront
Proceeds go back into the forum.
If you need to buy it anyway, use the affiliate link to help the forum.
Advertise Here