Author Topic: Convert Alloy wheels to Tubeless  (Read 861 times)

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Convert Alloy wheels to Tubeless
« on: November 02, 2026, 06:08:12 PM »



So I have my 1980 Convert and am converting the cast alloy wheels to tubeless. Spent the better part of three hours sanding and polishing the rim area that contacts the tire bead to remove all corrosion and guarantee an airtight seal.

Now it comes time to mount an appropriate Schrader valve. The rim hole for the valve is 0.335". The drop center is a deep radius and does not lend itself to the regular flanged schrader valves. Radius looks too deep to countersink for a flat for a seal.



Base flange on this unit tangles with radius in drop center of rim unless I remachine the rim, which I don't want to do.

Now the 0.335" hole in the rim is the perfect diameter for a 1/8" NPT thread.



This valve would thread into that tapped hole. I would install it with Loctite RC680 to guarantee both a positive seal and retention.

Now I'm open to any suggestions for alternate solutions as I'm not looking to reinvent the wheel. What is everyone else doing for tubeless valve stems with these Moto Guzzi rims?
« Last Edit: November 02, 2026, 06:14:02 PM by n3303j »
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Online PeteS

  • Gaggle Hero
  • *****
  • Posts: 3798
Re: Convert Alloy wheels to Tubeless
« Reply #1 on: November 02, 2026, 08:01:47 PM »
Been about thirty years since I did this on my ‘76 LeMans, (same wheels??) but I just used a counterbore to flatten the inside surface. Then used a common Schrader valve with the best fit. I have a set where multiple pilots fit the same cutter but you can get individual ones on Amazon. Just search on counterbore.





Pete

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Convert Alloy wheels to Tubeless
« Reply #2 on: November 02, 2026, 08:22:22 PM »
Been about thirty years since I did this on my ‘76 LeMans, (same wheels??) but I just used a counterbore to flatten the inside surface. Then used a common Schrader valve with the best fit. I have a set where multiple pilots fit the same cutter but you can get individual ones on Amazon. Just search on counterbore.





Pete
Old die maker here. I have piloted counterbores on hand but feel that by the time the low section is flat the outer edges of the counterbore might break through the rim
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Online PeteS

  • Gaggle Hero
  • *****
  • Posts: 3798
Re: Convert Alloy wheels to Tubeless
« Reply #3 on: November 02, 2026, 08:29:17 PM »
Do what you are comfortable with but this bike has many miles on it since I did this including dozens of track days.
Still holds air.

Pete

Online BMCMOTO

  • Gaggle Hero
  • *****
  • *
  • Posts: 954
  • Location: East Lansing, MI
Re: Convert Alloy wheels to Tubeless
« Reply #4 on: November 03, 2026, 06:02:40 AM »
If that rim is marked MT near the size marking, it is a tubeless rim. Most of that style I have encountered have been. Valves are available that work very well without much trouble.

MG Cycle has originals https://www.mgcycle.com/index.php?main_page=product_info&cPath=218&products_id=1032.

Measure the hole size and search on the metric hole size I think they're 11mm.
Oops, you did measure. .335 is about 8mm. Stems are available.

https://www.amazon.com/s?k=tubeless+alloy+wheel+valve+stem+8mm+rim+hole&channelId=500&clpRedir=Y&plpRedirect=mhFallback

Brian
« Last Edit: November 03, 2026, 06:08:00 AM by BMCMOTO »
1989 MILLE GT 
2006 BREVA 750
2004 BREVA 750     
1975 CONVERT

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Convert Alloy wheels to Tubeless
« Reply #5 on: November 03, 2026, 05:02:13 PM »
Do what you are comfortable with but this bike has many miles on it since I did this including dozens of track days.
Still holds air.

Pete
If that rim is marked MT near the size marking, it is a tubeless rim. Most of that style I have encountered have been. Valves are available that work very well without much trouble.

MG Cycle has originals https://www.mgcycle.com/index.php?main_page=product_info&cPath=218&products_id=1032.

Measure the hole size and search on the metric hole size I think they're 11mm.
Oops, you did measure. .335 is about 8mm. Stems are available.

https://www.amazon.com/s?k=tubeless+alloy+wheel+valve+stem+8mm+rim+hole&channelId=500&clpRedir=Y&plpRedirect=mhFallback

Brian

Nope, WM3 but going to run tubeless. After having two flats in one year, one tube and one tubeless, I noticed tubeless deflated slowly and gave me time to pull off road safely. Tube type dropped pressure immediately, came off the rim and left me with an uncontrollable motorcycle.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Convert Alloy wheels to Tubeless
« Reply #6 on: November 03, 2026, 05:32:43 PM »
Meanwhile Guzzi sent me a hidden message when the rim valve stem hole was the exact diameter of a Q letter drill which just happens to be the specified drill for a 1/8" NPT Tap.






So it's installed with Loctite RC680 and will be mounted tubeless tomorrow.
« Last Edit: November 03, 2026, 06:33:53 PM by n3303j »
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Offline brider

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 1615
Re: Convert Alloy wheels to Tubeless
« Reply #7 on: November 06, 2026, 08:08:44 AM »
Interesting...so the only thing stopping me from going tubeless on my Cal 2 (NOT bent-spoke, but otherwise the same?) is the stem? Simple tap of the existing hole and I'm good-to-go? I know this has been discussed a bazillion times but I guess I just never paid attention until now.

Bead design is the same, tube or tubeless?
'85 Cal II Auto
'71 Ambo project
'02 GasGas EC300
'07 Norge
'05 KTM 950 Adventure
Wish'd I'd never sold:
'72 Red Eldo
'74 White Eldo LAPD
'77 Convert with DB bags
'06 Gas Gas EC300
'86 LM IV

Online faffi

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • Posts: 1473
  • Bloody foreigner from Norway
Re: Convert Alloy wheels to Tubeless
« Reply #8 on: November 06, 2026, 08:19:02 AM »
AFAIK, the bead design is the same between all the early, narrow (2.15") cast Guzzi rims, tubeless or tube type. It was the same with Suzuki, Kawasaki and Yamaha back around circa 1980. Honda made different wheels (ComStar) which apparently differed in bead designs between tubeless and tube type, but you could still run tubeless on the tube type. What all the tube-type beads lack, is the safety hump. IMO, it is still safer to run tubeless because a normal puncture will be fairly slow without a tube, allowing you time to stop under control. A tube tend to lose air pressure rapidly, which can lead the tire to fall off the bead before you can stop, possibly leading to a crash.
Current bikes:
2002 BT1100
1982 XV750 / 1990 1100 mongrel
1990 XT600Z
2001 NT650V in bits

Offline n3303j

  • Ron Cichowski
  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • *
  • Posts: 2164
  • Location: Eastern Massachusetts
Re: Convert Alloy wheels to Tubeless
« Reply #9 on: November 06, 2026, 08:23:34 AM »
Interesting...so the only thing stopping me from going tubeless on my Cal 2 (NOT bent-spoke, but otherwise the same?) is the stem? Simple tap of the existing hole and I'm good-to-go? I know this has been discussed a bazillion times but I guess I just never paid attention until now.

Bead design is the same, tube or tubeless?
Bead design is DIFFERENT. There is no "safety bead" to retain the tire on the WM3 rim. There is a "safety bead" to retain the tire on an MT rim.
BUT
You regularly run tubeless tires on a WM3 rim with a tube installed.
When the tire deflates it will come off that WM3 more readily than an MT rim.
So with or without a tube installed the deflated tire will readily depart the WM3 rim bead.
In my experience a nail hole in a tubeless tire deflates more slowly than the same nail hole in a tube tire. Matter of fact if the nail stays in place there is no deflation on the tubeless  tire.
So running tubeless gives me a longer time to deal with an en route puncture emergency than the tube equivalent.
'98 MG V11 EV
'96 URAL SPORTSMAN
'77 MG 850T3 FB

Online faffi

  • Gaggle Hero
  • *****
  • *
  • *
  • *
  • Posts: 1473
  • Bloody foreigner from Norway
Re: Convert Alloy wheels to Tubeless
« Reply #10 on: November 06, 2026, 09:00:08 AM »
I was under the impression that Guzzi, like the Japanese manufacturers, sold the old narrow 2.15" rimmed wheels also as tubeless. Cudos to them if they did not, and that it was only when rim width grew to 2.50 and more that tubeless became a thing, with the apporpriate bead design.
Current bikes:
2002 BT1100
1982 XV750 / 1990 1100 mongrel
1990 XT600Z
2001 NT650V in bits

 

Shop our affiliate storefront
Proceeds go back into the forum.
If you need to buy it anyway, use the affiliate link to help the forum.
Advertise Here